Here you can exchange your experience and datas about your home build boards
-
badgb21
- Very Frequent Poster
- Posts: 659
- Joined: Mon Jun 16, 2003 8:55 am
- Favorite Beaches: High Pines - Duxbury
Chapin/Mayflower Cape Cod
Langebaan
Cape Verde
- Gear: None
- Brand Affiliation: None. - The words of the prophets are written on the forum “walls”-
- Location: Hants UK
-
Has thanked:
34 times
-
Been thanked:
29 times
Postby badgb21 » Tue Apr 19, 2016 3:56 pm
Thanks, the two sizes look ideal.
(Have ordered direct as USA and UK sellers don't seem to sell this pack?)
Update: the packs arrived promptly and just what I wanted. Thanks,
Gigi;) wrote:Here you go:
http://drtuba.eu/all-kite-products/repa ... epair-dots
badgb21 wrote:Hi
I'm looking to renew my stock of pre-cut round (or rounded corner) bladder patches, approx. 1" diameter. Looking for best patches and a source.
Suitable of Cabrinha and Ozone bladders.
I got lost in 26 pages in this thread and a search threw up 800+ results, so forgive me if this had been covered already.
Thanks
-
OzBungy
- Very Frequent Poster
- Posts: 2759
- Joined: Fri Oct 21, 2005 11:35 am
-
Has thanked:
6 times
-
Been thanked:
220 times
Postby OzBungy » Wed May 25, 2016 1:22 pm
When using tape to repair a canopy tear, fill a bottle with hot water and use it as a roller to smooth out wrinkles and bubbles and to hot set the glue. You can also use a pot of hot water as an iron. I prefer the bottle method.
-
Gigi;)
- Very Frequent Poster
- Posts: 556
- Joined: Wed Jan 12, 2005 7:23 pm
- Location: drtuba.eu, kite-stuff.org, eXtremist.si, kajtar.si
-
Has thanked:
2 times
-
Been thanked:
12 times
-
Contact:
Postby Gigi;) » Wed May 25, 2016 3:10 pm
Thank you & ride hard!!
[quote="badgb21"Thanks, the two sizes look ideal.
(Have ordered direct as USA and UK sellers don't seem to sell this pack?)
Update: the packs arrived promptly and just what I wanted. Thanks,
Gigi;) wrote:Here you go:
http://drtuba.eu/all-kite-products/repa ... epair-dots
badgb21 wrote:Hi
I'm looking to renew my stock of pre-cut round (or rounded corner) bladder patches, approx. 1" diameter. Looking for best patches and a source.
Suitable of Cabrinha and Ozone bladders.
I got lost in 26 pages in this thread and a search threw up 800+ results, so forgive me if this had been covered already.
Thanks
[/quote]
-
corbett
- Very Frequent Poster
- Posts: 717
- Joined: Fri Dec 13, 2002 1:00 am
- Gear: Many
- Brand Affiliation: None
- Location: Near Moscow
-
Has thanked:
0
-
Been thanked:
0
Postby corbett » Thu May 26, 2016 4:48 pm
Bar:
Is your popular CL826-11AN Clam Cleat needing to be replaced? perhaps the teeth aren't gripping the rope so well anymore?
If you keep the black plastic part and screw on a replacement CL211 Mk2AN, you will save money.
CL826-11AN RRP£11.20
CL211 Mk2AN RRP£6.30
-
Toby
- Very Frequent Poster
- Posts: 50499
- Joined: Mon Sep 24, 2001 1:00 am
- Kiting since: 2000
- Weight: 95 kg
- Local Beach: Cumbuco, Brazil
Barra do Cauipe, Brazil
- Favorite Beaches: same
- Style: Airstyle
- Gear: Rebel 2015 18
- Brand Affiliation: None.
- Location: World (KF Admin)
-
Has thanked:
842 times
-
Been thanked:
2396 times
-
Contact:
Postby Toby » Tue Jun 28, 2016 1:20 pm
-
ragzilla
- Medium Poster
- Posts: 159
- Joined: Tue Oct 13, 2015 10:59 am
- Local Beach: none
- Favorite Beaches: none
- Style: break shit!!!!!
- Gear: slingy
- Brand Affiliation: None
-
Has thanked:
0
-
Been thanked:
1 time
Postby ragzilla » Wed Jun 29, 2016 6:00 am
ive got a really good trick to installing bladders.
i line my bladders 10/10 everytime.
when pulling the bladder with string...... dont pull the string from the wing tip...... instead, pull the string from the valve holes in the LE...... instead of pulling from 3m away, you are only pulling 1m at a time..........
when you get to the last valve hole (roughly where the LE curve is)... I put my foot 20cm from the hole and pull. that wayy the bladder cant pass my foot and im doing it in small intervals. .... this is only good for where the curve is.
also.... dont install the curve flat on the ground..... if you keep the LE flat, you will actually see that the seam curves around.
keep your foot on the LE and the ground .... and bring the wing tip vertical..... this will stop the bladder twisting..... when the bladder stops at your foot , move your foot 20cm closer to the wingtip (keeping the LE seam in line).... and repeat..... wingtip vertical and pull.
my theory is.... and its been working everytime since i did it this way.....
its not the bladder that twists..... its the LE that twists...... if you think about it..... when the kite is pumped up the bladder doesnt sit flat on the ground...... the kite has a curve.
kite smaller than 11m are no problem.
but kite 11m+ this is the way to go!!!
-
kjorn
- Very Frequent Poster
- Posts: 831
- Joined: Tue Feb 11, 2003 10:42 am
- Brand Affiliation: None
- Location: uk
-
Has thanked:
55 times
-
Been thanked:
29 times
-
Contact:
Postby kjorn » Fri Jul 15, 2016 1:20 pm
corbett wrote:Bar:
Is your popular CL826-11AN Clam Cleat needing to be replaced? perhaps the teeth aren't gripping the rope so well anymore?
If you keep the black plastic part and screw on a replacement CL211 Mk2AN, you will save money.
CL826-11AN RRP£11.20
CL211 Mk2AN RRP£6.30
Just adding some more keyphrases to this so google will pick it up for more searches (it took me ages to find the name of this cleat!) depower line, amsteel, 6mm, chickenloop, butterbox, mutiny, regulator cleat controller.
Another interesting cleat is the clamcleat cobra cl264.
-
gilana
- Medium Poster
- Posts: 133
- Joined: Sun Jun 22, 2014 1:34 am
- Kiting since: 2014
- Weight: 70KG
- Local Beach: We live on our sailing yacht and at the moment we are in the San Blas Islands of Panama, and we sometimes have visiting guests to come spend a week of wind with us...
Laura and Mike
- Favorite Beaches: Chameys in San Andres Isla Colombia
Yansaladup in Kuna Yala Panama
- Style: Old School
- Gear: Ozone Edge 9m V8
Ozone Edge 9m V9
Ozone Edge 10m V9
Caution Santa Cruz Redline 132 TT
Epic Droid V2 135x41 TT
Chemical 132 TT
North Directional
- Brand Affiliation: None, I wish.
- Location: San Blas Panama
-
Has thanked:
3 times
-
Been thanked:
1 time
-
Contact:
Postby gilana » Mon Aug 08, 2016 10:00 pm
Here in San Andres, Colombia, we just replaced all the bladders in our 9m 2012 Ozone Edge, cant wait till tomorrow.
The old bladders were not leaking, just the one-pump connector pipes were breaking.
Love my (new) kite, and 2012 might sound old to you but I am a 1960 model so what?
What to do with the old bladders???
They make nice "Dry Bags" Cut to size and weld up with a vacuum baggie machine, then roll the top and knot it. Keeps your phone, camera, or sandwiches dry...
-
maoz
- Rare Poster
- Posts: 1
- Joined: Wed Apr 29, 2009 9:11 pm
- Local Beach: Israel, Herzelia Tel-Aviv Bait-Yanai
- Gear: Naish Calt
- Brand Affiliation: None
-
Has thanked:
0
-
Been thanked:
0
Postby maoz » Sat Apr 22, 2017 5:41 pm
Hi, I wish to replace bladder on Naish Helix 10m 2010 and park 9m 2011, I want to replace all the bladder system with not "one pump system" (I don't like the Naish octopus system)
does anyone know wich bladders can fit, and where can I find it with reasonable price?
thanks!
-
stephk
- Medium Poster
- Posts: 73
- Joined: Thu May 15, 2008 3:16 am
- Local Beach: Oka, Quebec
Lachine, Quebec
Valois bay, Quebec
Pointe-Claire, Quebec
Venise en Quebec, Quebec
- Favorite Beaches: Cape Cod
Waquoit bay, Cape Cod
Cape Hatteras, NC
- Style: freeride
- Gear: Epic, Cabrinha, Kiteaid
- Location: Canada
-
Has thanked:
0
-
Been thanked:
0
-
Contact:
Postby stephk » Sat Apr 22, 2017 5:54 pm
Return to “Gear Builders”
Who is online
Users browsing this forum: No registered users and 149 guests