Contact   Imprint   Advertising   Guidelines

Building a Plywood Shinnster / BRM Paipo

Here you can exchange your experience and datas about your home build boards
icedub
Rare Poster
Posts: 18
Joined: Wed Aug 23, 2017 9:18 pm
Local Beach: Lake Champlain, Vermont
Style: Freeride
Gear: Switch Element v4: 5m, 7m
Switch Element v6: 9m, 12m
Boards: Axis Division TT and Homemade Shinnster "The Spinster"
Brand Affiliation: None
Has thanked: 0
Been thanked: 0

Building a Plywood Shinnster / BRM Paipo

Postby icedub » Thu Aug 24, 2017 3:09 pm

Hi All! I'm new to board building and this forum, so hopefully this isn't too dumb of a question:

I'm planning to trace my buddy's Shinn Shinnster and do a simple plywood version. I know this board has pretty decent flex, and having never built a plywood board, I'm curious what this forum might recommend for a good plywood thickness. I can source 1/4" or 1/2" poplar ply from a local distributor. My hunch is that at 160cm long, 1/4" ply will be too flexible, but I'd love to hear from anyone who has built a similar style board!

Image

faklord
Frequent Poster
Posts: 474
Joined: Sun Jan 09, 2011 6:03 pm
Brand Affiliation: None
Has thanked: 35 times
Been thanked: 80 times

Re: Building a Plywood Shinnster / BRM Paipo

Postby faklord » Thu Aug 24, 2017 8:37 pm

I know a few people who have done this using two layers of 6mm (1/4") ply laminated together to 'set' some rocker. And then add a layer of glass cloth top and bottom. They ride fine but are a bit heavy. Very smooth on the water (even smoother than a genuine shinnster!) but probably a bit too heavy for flips & tricks.

direnc
Frequent Poster
Posts: 204
Joined: Sun Jul 22, 2012 11:50 pm
Kiting since: 2009
Local Beach: Alacati, Pirlanta, Ilica
Style: Freeride
Gear: Cult 7.5
Soul 10
Ride 10
Kestrel 12
Gin Spirit 15
Edge 8/9/11
Ten Velox 11
Zephyr
Mako 150, DIY foils and boards
Brand Affiliation: None
Has thanked: 47 times
Been thanked: 21 times

Re: Building a Plywood Shinnster / BRM Paipo

Postby direnc » Thu Aug 24, 2017 10:07 pm

Imo, two 4mm layers should be enough with some fiberglass. If you add a bit of concave, it'll probably be stiff enough with minimal amount of glass.

icedub
Rare Poster
Posts: 18
Joined: Wed Aug 23, 2017 9:18 pm
Local Beach: Lake Champlain, Vermont
Style: Freeride
Gear: Switch Element v4: 5m, 7m
Switch Element v6: 9m, 12m
Boards: Axis Division TT and Homemade Shinnster "The Spinster"
Brand Affiliation: None
Has thanked: 0
Been thanked: 0

Re: Building a Plywood Shinnster / BRM Paipo

Postby icedub » Fri Aug 25, 2017 8:47 pm

direnc wrote:
Thu Aug 24, 2017 10:07 pm
Imo, two 4mm layers should be enough with some fiberglass. If you add a bit of concave, it'll probably be stiff enough with minimal amount of glass.
Does adding concave make the board stiffer somehow?

icedub
Rare Poster
Posts: 18
Joined: Wed Aug 23, 2017 9:18 pm
Local Beach: Lake Champlain, Vermont
Style: Freeride
Gear: Switch Element v4: 5m, 7m
Switch Element v6: 9m, 12m
Boards: Axis Division TT and Homemade Shinnster "The Spinster"
Brand Affiliation: None
Has thanked: 0
Been thanked: 0

Re: Building a Plywood Shinnster / BRM Paipo

Postby icedub » Fri Aug 25, 2017 8:49 pm

faklord wrote:
Thu Aug 24, 2017 8:37 pm
I know a few people who have done this using two layers of 6mm (1/4") ply laminated together to 'set' some rocker. And then add a layer of glass cloth top and bottom. They ride fine but are a bit heavy. Very smooth on the water (even smoother than a genuine shinnster!) but probably a bit too heavy for flips & tricks.
Interesting. So using 2 layers just allows you to set rocker into it? I was going to go with the soak and weight method. Hoping that a single sheet of 1/2" will be slightly flexible and not too stiff.

faklord
Frequent Poster
Posts: 474
Joined: Sun Jan 09, 2011 6:03 pm
Brand Affiliation: None
Has thanked: 35 times
Been thanked: 80 times

Re: Building a Plywood Shinnster / BRM Paipo

Postby faklord » Sat Aug 26, 2017 8:34 am

icedub wrote:
Fri Aug 25, 2017 8:47 pm
direnc wrote:
Thu Aug 24, 2017 10:07 pm
Imo, two 4mm layers should be enough with some fiberglass. If you add a bit of concave, it'll probably be stiff enough with minimal amount of glass.
Does adding concave make the board stiffer somehow?
Yes. But
1) it's quite difficult to build in concave and rocker at the same time, using ply. (I have done this , on a TT, using 3 layers of 4mm ply but it required quite a lot of force and a sturdy jig to hold it in place while the epoxy set...it wasn't great)
2) the ride would likely be quite different to a Shinnster.

faklord
Frequent Poster
Posts: 474
Joined: Sun Jan 09, 2011 6:03 pm
Brand Affiliation: None
Has thanked: 35 times
Been thanked: 80 times

Re: Building a Plywood Shinnster / BRM Paipo

Postby faklord » Sat Aug 26, 2017 8:45 am

icedub wrote:
Fri Aug 25, 2017 8:49 pm
faklord wrote:
Thu Aug 24, 2017 8:37 pm
I know a few people who have done this using two layers of 6mm (1/4") ply laminated together to 'set' some rocker. And then add a layer of glass cloth top and bottom. They ride fine but are a bit heavy. Very smooth on the water (even smoother than a genuine shinnster!) but probably a bit too heavy for flips & tricks.
Interesting. So using 2 layers just allows you to set rocker into it? I was going to go with the soak and weight method. Hoping that a single sheet of 1/2" will be slightly flexible and not too stiff.
You still get quite a bit of spring back if you set the rocker using 2 layers (more layers, less spring back)

If you can persuade a single sheet of 1/2" to hold its rocker, long term, that should be fine. Personally I think I would still put a layer of glass top and bottom, both to help hold the rocker and also for protection.

One option might be to:
Bend your ply
Glass top surface
Thin out nose and tail sections (using plane/sander)..this will loose a bit of weight & distribute the flex to be more like the genuine article.
Glass bottom surface.

Enjoy

jannik
Medium Poster
Posts: 148
Joined: Wed Nov 17, 2010 10:39 am
Brand Affiliation: None
Location: Denmark
Has thanked: 4 times
Been thanked: 20 times

Re: Building a Plywood Shinnster / BRM Paipo

Postby jannik » Tue Aug 29, 2017 1:13 pm

If you have access to paulownia wood I think it is a better option. Certainly lighter. I have been building wooden kite surfboards by making a wooden stringer and then glueing wood around that stringer, plane it out, and then trace and cut the outline. Glassing is up for debate. I've used everything from linseed oil to glassfiber felt for walls :) The next few boards will have e-glass on them.

These are build that way:
20150712_212117.jpg
P70510-231820.jpg
P70518-070710.jpg

User avatar
jeromeL
Very Frequent Poster
Posts: 1114
Joined: Thu Sep 04, 2014 6:22 pm
Local Beach: Longisland NY
Style: freestyle
Gear: Fone Bandit 2014 12m^2, 2015 9, 2015 7, 2015 14
Best GP 2015 9m
Star Sirius V2 12m
Nobile Fity/50 138cm
Naish Apex bindings.
Zeeko Green and White + Shinn El Stubbo
Brand Affiliation: None
Location: Longisland, NY, USA
Has thanked: 0
Been thanked: 2 times
Contact:

Re: Building a Plywood Shinnster / BRM Paipo

Postby jeromeL » Tue Aug 29, 2017 5:36 pm

jannik wrote:
Tue Aug 29, 2017 1:13 pm
If you have access to paulownia wood I think it is a better option. Certainly lighter. I have been building wooden kite surfboards by making a wooden stringer and then glueing wood around that stringer, plane it out, and then trace and cut the outline. Glassing is up for debate. I've used everything from linseed oil to glassfiber felt for walls :) The next few boards will have e-glass on them.
So you get most of the rocker thanks to stringer?

jannik
Medium Poster
Posts: 148
Joined: Wed Nov 17, 2010 10:39 am
Brand Affiliation: None
Location: Denmark
Has thanked: 4 times
Been thanked: 20 times

Re: Building a Plywood Shinnster / BRM Paipo

Postby jannik » Tue Aug 29, 2017 9:46 pm

I get all my rocker from the stringer. Wood is glued onto the stringer like this
gluing.png
and planed to a blank like this:
blank.png


Return to “Gear Builders”

Who is online

Users browsing this forum: No registered users and 47 guests