Contact   Imprint   Advertising   Guidelines

DIY split wave twinny

Here you can exchange your experience and datas about your home build boards
User avatar
Greenturtle
Very Frequent Poster
Posts: 978
Joined: Fri May 12, 2017 6:51 pm
Local Beach: Presque Isle, Erie PA
Favorite Beaches: Bahamian Cays
Gear: Edge 19, Flite 17, 14.5, 12, 10, 8, Cloud 13.4, 10.4, 8, 6.2, 3.7
Tons of boards for water, land, and snow
Brand Affiliation: None
Has thanked: 240 times
Been thanked: 276 times

Re: DIY split wave twinny

Postby Greenturtle » Wed Dec 13, 2017 4:09 am

Wicked nice build! That is a board to be proud of, and very practical.
Thanks for posting.

plummet
Very Frequent Poster
Posts: 6819
Joined: Sat Aug 29, 2009 11:25 pm
Local Beach: EE
Favorite Beaches: NZ
Style: Terrain riding
Gear: Old wornout ozone.
Plummet hydrofoil and mutant
Brand Affiliation: None
Has thanked: 11 times
Been thanked: 224 times

Re: DIY split wave twinny

Postby plummet » Wed Dec 13, 2017 7:32 am

Awesome build. I do worry that you have created a stress riser at the plate end. I would have radiused the carbon reinforcement so dispersion the stress loading away from the plate.

User avatar
rynhardt
Very Frequent Poster
Posts: 977
Joined: Wed Sep 11, 2013 3:51 pm
Local Beach: Langebaan
Favorite Beaches: Langebaan
Style: Freeride
Gear: Cloud C2 17
Hoff Twinwave
Brand Affiliation: None
Location: Johannesburg, South Africa
Has thanked: 24 times
Been thanked: 29 times

Re: DIY split wave twinny

Postby rynhardt » Wed Dec 13, 2017 2:40 pm

TomW wrote:
Tue Dec 12, 2017 11:35 pm
Nice work. I've been thinking about making a split hydrofoiling board.
I was thinking a plate on top and bottom.
The one on the bottom would extend under the hydrofoil mast plate and forward and the one on top would be flush with the deck pads, but only in the middle like your plate.

My board will be made with foam Core

Have to think about it.
Yeah two plates would be fine. They wouldn't need to be thick at all since they would be on both sides of the board. Like 300gsm carbon skins might even be enough.

User avatar
rynhardt
Very Frequent Poster
Posts: 977
Joined: Wed Sep 11, 2013 3:51 pm
Local Beach: Langebaan
Favorite Beaches: Langebaan
Style: Freeride
Gear: Cloud C2 17
Hoff Twinwave
Brand Affiliation: None
Location: Johannesburg, South Africa
Has thanked: 24 times
Been thanked: 29 times

Re: DIY split wave twinny

Postby rynhardt » Wed Dec 13, 2017 2:49 pm

plummet wrote:
Wed Dec 13, 2017 7:32 am
Awesome build. I do worry that you have created a stress riser at the plate end. I would have radiused the carbon reinforcement so dispersion the stress loading away from the plate.
I've tried to mitigate that by tapering the plate but yeah a radius on the inside edge of the plate edge would not hurt. Thanks for the tip!

TomW
Very Frequent Poster
Posts: 3585
Joined: Wed Oct 05, 2005 6:43 pm
Kiting since: 2001
Local Beach: Vejbystrand, Lomma
Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
Brand Affiliation: None
Location: Sweden
Has thanked: 53 times
Been thanked: 193 times

Re: DIY split wave twinny

Postby TomW » Wed Dec 13, 2017 10:32 pm

rynhardt wrote:
Wed Dec 13, 2017 2:40 pm
TomW wrote:
Tue Dec 12, 2017 11:35 pm

Yeah two plates would be fine. They wouldn't need to be thick at all since they would be on both sides of the board. Like 300gsm carbon skins might even be enough.
I did some measuring and marking on my foil board last night.
The bottom part that goes under the plate could be 200mm wide and 700mm long.
If I make it with laminated veneer wood Core like 5 mm thick and cover it with uniD cf and glass, taper thickness towards nose. I would fasten the 675mm long board halves to it. Sort of like the Shinn approach.
Then with 2 small plates on top 50mm wide x 150 mm, close to each rail.
This keeps the deck plate out of the way of the front foothook I use.

I'm concerned this whole thing will bee too heavy.
And how for I pack a 93cm mast with plate??

User avatar
rynhardt
Very Frequent Poster
Posts: 977
Joined: Wed Sep 11, 2013 3:51 pm
Local Beach: Langebaan
Favorite Beaches: Langebaan
Style: Freeride
Gear: Cloud C2 17
Hoff Twinwave
Brand Affiliation: None
Location: Johannesburg, South Africa
Has thanked: 24 times
Been thanked: 29 times

Re: DIY split wave twinny

Postby rynhardt » Thu Dec 14, 2017 9:29 am

It's going to add weight, that much is unavoidable. Like at least 500g to 800g.
And unless you have a way of removing the plate from the mast, packaging is going to be a problem..

plummet
Very Frequent Poster
Posts: 6819
Joined: Sat Aug 29, 2009 11:25 pm
Local Beach: EE
Favorite Beaches: NZ
Style: Terrain riding
Gear: Old wornout ozone.
Plummet hydrofoil and mutant
Brand Affiliation: None
Has thanked: 11 times
Been thanked: 224 times

Re: DIY split wave twinny

Postby plummet » Thu Dec 14, 2017 10:44 am

TomW wrote:
Wed Dec 13, 2017 10:32 pm
rynhardt wrote:
Wed Dec 13, 2017 2:40 pm
TomW wrote:
Tue Dec 12, 2017 11:35 pm

Yeah two plates would be fine. They wouldn't need to be thick at all since they would be on both sides of the board. Like 300gsm carbon skins might even be enough.
I did some measuring and marking on my foil board last night.
The bottom part that goes under the plate could be 200mm wide and 700mm long.
If I make it with laminated veneer wood Core like 5 mm thick and cover it with uniD cf and glass, taper thickness towards nose. I would fasten the 675mm long board halves to it. Sort of like the Shinn approach.
Then with 2 small plates on top 50mm wide x 150 mm, close to each rail.
This keeps the deck plate out of the way of the front foothook I use.

I'm concerned this whole thing will bee too heavy.
And how for I pack a 93cm mast with plate??
2 thoughts for you Tom.

Why not make a 93cm board not split?
Or don't split down the middle 93cm gives you your foot stance and foil attachment. Make a bolt on nose. That way it doesn't need the strength of a half split board. It just needs to withstand touch downs. Less reinforcement, less bolts, less weight.

TomW
Very Frequent Poster
Posts: 3585
Joined: Wed Oct 05, 2005 6:43 pm
Kiting since: 2001
Local Beach: Vejbystrand, Lomma
Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
Brand Affiliation: None
Location: Sweden
Has thanked: 53 times
Been thanked: 193 times

Re: DIY split wave twinny

Postby TomW » Thu Dec 14, 2017 5:04 pm

Plummet,

Interesting thought. 93cm just enough to get the mast on, and hooks.
Nose would be about 400mm long.

Needs a lot more thought and design it to fit a particular bag or suitcase..

User avatar
rynhardt
Very Frequent Poster
Posts: 977
Joined: Wed Sep 11, 2013 3:51 pm
Local Beach: Langebaan
Favorite Beaches: Langebaan
Style: Freeride
Gear: Cloud C2 17
Hoff Twinwave
Brand Affiliation: None
Location: Johannesburg, South Africa
Has thanked: 24 times
Been thanked: 29 times

Re: DIY split wave twinny

Postby rynhardt » Thu Dec 28, 2017 10:17 am

Removed about 300g from the top strap (plate).
Plus I think it also looks a bit more kick-ass :D
Attachments
DSC_0112.JPG

Grkite
Medium Poster
Posts: 51
Joined: Sun Dec 06, 2015 3:29 pm
Local Beach: Paros - Pounda
Naxos-Mikri vigla
Mastichari-Kos
Favorite Beaches: Paros-Pounda
Gear: Cabrinha 2014 Vector 11
Cabrinha 2017 Switcblade 8
My handmade boards-HYPERION KITEBOARDS
Brand Affiliation: None
Has thanked: 0
Been thanked: 0
Contact:

Re: DIY split wave twinny

Postby Grkite » Sat Jan 13, 2018 1:02 pm

You make it looks soo easy....:)

But I wonder about the graphichs. Did you print in the polyester fabric? Where? Or you bought this as is ?

Thanks.


Return to “Gear Builders”

Who is online

Users browsing this forum: No registered users and 53 guests