Contact   Imprint   Advertising   Guidelines

Nomad's DIY foil build

A forum dedicated to Hydrofoil riders
NorCalNomad
Very Frequent Poster
Posts: 838
Joined: Thu Feb 13, 2014 4:40 am
Local Beach: San Francisco
Gear: Why should it matter?
Has thanked: 0
Been thanked: 3 times

Re: Nomad's DIY foil build

Postby NorCalNomad » Mon Mar 20, 2017 9:41 pm

Yeah that whole sanding thing really pissed me off. Finally got all the surfaces ready for carbon and definitely going about it differently this time.

If you want to follow some small updates through instagram I'm tagging (and back tagged) all my posts with #nomadfoil.

Right now I've gotten a layer of 6oz twill CF on both sides of my fuselage (with it overlapping on my at the top and bottom surfaces + triaxial glass underneath it. Trying to decide if I want to or need to put on more since it's already feels REALLY stiff. Definitely going to put some reinforcement patches at the nose and tail where they are most likely to get banged around in the water and car. And other than putting more carbon to stiffen/ blend the mast into the fuselage I think I'm good for the fuselage.

Now the mast still needs a few layers since I didn't get to put on my full layup when I had my hardener miscalculation. Then attach it permanently to the baseplate (lots of CF).

Wings need to get a layer of 6oz CF twill then they'll be done. Wondering if I should put on a layer of 4 or 2oz glass on top of the CF just to make them a little more ding resistant, or just do a heavy sanding coat?

And for the board I still need to figure out what I'm doing. Not sure if it will float, so I'm wondering if bolting it to a skim would be a good idea... or should I try to do a simple XPS board (no rocker table, just carving and laminating) that will have tracks in them (like the alien air). I HAD a beat up Lost V3 that had the nose broken off but it had tons of dents in it that seemed like a pain in the ass to put more glass/ CF on for reinforcement.

NorCalNomad
Very Frequent Poster
Posts: 838
Joined: Thu Feb 13, 2014 4:40 am
Local Beach: San Francisco
Gear: Why should it matter?
Has thanked: 0
Been thanked: 3 times

Re: Nomad's DIY foil build

Postby NorCalNomad » Thu Apr 20, 2017 6:11 am

Holy shit did work get busy in March and April.

Fuselage is done.

Got some cheap G10 wings from a school when a student mangled them good. Which is great since I won't have to try to fix the meathook abortion experimental lamination technique that I tried on the fins. Do need to slightly adjust the hole pattern but that's a couple minute job.

Mast got another layer of 5.7oz 12k unil and 6oz 3k twill CF, with no air bubbles! Trimmed the excess on the trailing edge and need to sand it down to it's final trailing edge thickness. Only construction bit left to do it trim it to it's final length.

Baseplate still needs to go on, got some good CF trimmings/ scraps for building up that transition.

Once the baseplate is on I'll "hotcoat" the fuselage/mast/baseplate with a white tint.

I snapped my 5'2" Vanguard in half jumping, not too smart on a Rapidfire construction board. So I'm going to put that back together, reinforce, and put single fin or mast tracks into that for my board.

NorCalNomad
Very Frequent Poster
Posts: 838
Joined: Thu Feb 13, 2014 4:40 am
Local Beach: San Francisco
Gear: Why should it matter?
Has thanked: 0
Been thanked: 3 times

Re: Nomad's DIY foil build

Postby NorCalNomad » Mon Apr 24, 2017 6:08 pm

Got a bit of work done on stuff over the weekend. Been posting photos to my instragram with the hashtag #nomadfoil http://view-instagram.com/hashtag/nomadfoil

All that is left on the foil assembly is to finish reinforcing the mast to plate connection, some wing to fuselage finishing, then a white "hotcoat"

For the board I filled back in the snap in my vanguard with PU pour foam, and ordered fin boxes and T-nuts from Chinook. Going to work on reinforcing the snapped joint and the topside of the board while I wait for the boxes to come in. Was tempted to get one of those Houston Kiteboarding stick on mounts until I saw the price O.O ($160). When the boxes come in I'll finish reinforcing the bottom and throw those boxes in.

NorCalNomad
Very Frequent Poster
Posts: 838
Joined: Thu Feb 13, 2014 4:40 am
Local Beach: San Francisco
Gear: Why should it matter?
Has thanked: 0
Been thanked: 3 times

Re: Nomad's DIY foil build

Postby NorCalNomad » Thu Apr 27, 2017 12:41 am

fack >.<

Hate buying expensive 316 metric fasteners off Mcmaster only to realize that they are going to be 5-10mm too short. Oh well, still will probably be cheaper than buying them through West Marine or another boating store...talk about inflation...

My Chinook fin boxes came in and I'm going to borrow my coworker's router to make that a clean operation. Was waiting for these so that I didn't have to do multiple stages of FG and CF on the bottom of the vanguard.

This weekend is travel but this should all be finished mid May. :D

NorCalNomad
Very Frequent Poster
Posts: 838
Joined: Thu Feb 13, 2014 4:40 am
Local Beach: San Francisco
Gear: Why should it matter?
Has thanked: 0
Been thanked: 3 times

Re: Nomad's DIY foil build

Postby NorCalNomad » Thu May 04, 2017 10:02 pm

All the construction on the foil is done, now it's just hotcoat and finish sand time. Got the first side done last night and tonight I should have the other side covered. Again the hashtag #nomadfoil gets you the pictures I've put on instagram
Image

Working on sanding the Vanguard for repairing the buckle and reinforcements. It seems like Firewire resin more resilient to sanding than any other boards I've done ding repairs on. I also have the boxes all prepped once I cut the holes.
I'm thinking of reinforcing the deck with at least one more layer of 4oz cloth...maybe 6oz but not wrapping the rails. The bottom is going to get another layer of 4oz, and carbon. Haven't decided if I'm just going to use 6oz twill + some unidirectional strips or if I should use the burly biaxial cloth over the boxes.

User avatar
rynhardt
Very Frequent Poster
Posts: 979
Joined: Wed Sep 11, 2013 3:51 pm
Local Beach: Langebaan
Favorite Beaches: Langebaan
Style: Freeride
Gear: Cloud C2 17
Hoff Twinwave
Brand Affiliation: None
Location: Johannesburg, South Africa
Has thanked: 25 times
Been thanked: 29 times

Re: Nomad's DIY foil build

Postby rynhardt » Fri May 05, 2017 9:31 pm

:thumb: Almost there..

NorCalNomad
Very Frequent Poster
Posts: 838
Joined: Thu Feb 13, 2014 4:40 am
Local Beach: San Francisco
Gear: Why should it matter?
Has thanked: 0
Been thanked: 3 times

Re: Nomad's DIY foil build

Postby NorCalNomad » Tue May 23, 2017 2:40 am

Haven't been posting on here, but I have on my instagram.

1. Finished it to a level I could ride it!
2. IT VERKZ!!!
3. Shins and rails do not get along :(... back to playing with fiberglass and resin.

https://www.instagram.com/p/BUap7taFREv/

Over the coming weeks I'll update the bit at the start for better documentation of the build.

User avatar
rynhardt
Very Frequent Poster
Posts: 979
Joined: Wed Sep 11, 2013 3:51 pm
Local Beach: Langebaan
Favorite Beaches: Langebaan
Style: Freeride
Gear: Cloud C2 17
Hoff Twinwave
Brand Affiliation: None
Location: Johannesburg, South Africa
Has thanked: 25 times
Been thanked: 29 times

Re: Nomad's DIY foil build

Postby rynhardt » Tue May 23, 2017 7:07 am

That's a serious dent!
Need to get yourself some of these :-)
Attachments
images.jpg
images.jpg (18.45 KiB) Viewed 722 times

TomW
Very Frequent Poster
Posts: 3585
Joined: Wed Oct 05, 2005 6:43 pm
Kiting since: 2001
Local Beach: Vejbystrand, Lomma
Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
Brand Affiliation: None
Location: Sweden
Has thanked: 53 times
Been thanked: 193 times

Re: Nomad's DIY foil build

Postby TomW » Tue May 23, 2017 11:20 am

Awesome work ethic. Nice to see.


Return to “Hydrofoil”

Who is online

Users browsing this forum: bitxopalo, cglazier, mede, nixmatters, Turbaani and 168 guests