Contact   Imprint   Advertising   Guidelines

Search found 1423 matches

Go to advanced search

by kitexpert
Thu Feb 29, 2024 11:27 am
Forum: Kitesurfing
Topic: Stalling 10m Evo 2021
Replies: 27
Views: 1686

Re: Stalling 10m Evo 2021

If kite backstalls after takeoff you are asking for it too much or you do it wrong. Meaning wind is too weak, kite is too small, kiter is too heavy and his edging is too weak and takeoff speed too low. Kite trim is simple: flying line lengths must be equal and then backlines are attached to middle k...
by kitexpert
Thu Feb 29, 2024 10:42 am
Forum: Kitesurfing
Topic: Tech Cast #12 | Feat. The Line Smith | Episode # 341
Replies: 29
Views: 2490

Re: Tech Cast #12 | Feat. The Line Smith | Episode # 341

I also pre load the lines before measuring them as a pair and make the splice with an extra long 20cm bury and always taper the line ends to give a smooth transition between the splice and line. Which splice do you use? Brummel, locked Brummel or simple eye splice with stitches? Your bury length is...
by kitexpert
Wed Feb 28, 2024 12:30 pm
Forum: Snow / Land
Topic: Want to break the Woo World Record, go snowkiting
Replies: 43
Views: 2155

Re: Want to break the Woo World Record, go snowkiting

It would be cool if Woo had a separate Portal for snowkiting. Especially, if the Woo recorded glides. It isn't technically possible to measure glides (whatever that even means) because there is not much accelerations there. Woo is meant for measuring boosting and even that has many challenges (diff...
by kitexpert
Sat Feb 24, 2024 7:32 pm
Forum: Kitesurfing
Topic: This kite could change it all | Emergency Episode | The Megapod
Replies: 40
Views: 4891

Re: This kite could change it all | Emergency Episode | The Megapod

Anecdotal story how some kite is good or better than anything else LOL. Building hype is not quite enough, if you really have something special it should look like something special, to have new features/tech. This kite industry is boring. Best it can offer is new fabrics, welded seams, printed grap...
by kitexpert
Sat Feb 24, 2024 7:12 pm
Forum: Kitesurfing
Topic: Ozone Vortex Ultra-X
Replies: 66
Views: 9245

Re: Ozone Vortex Ultra-X

they seem to have similar design: 7 point bridle for dlab and 8 point for Vortex for extra stability, both 3 strut / big air kites. That is something new, it is a bit like foil kite type bridle. Quite simple of course anyway but for LEI kite it is a lot. That should allow thinner LE and at least gi...
by kitexpert
Tue Feb 20, 2024 8:25 pm
Forum: Kitesurfing
Topic: Ozone Vortex Ultra-X
Replies: 66
Views: 9245

Re: Ozone Vortex Ultra-X

If you truly wanna have fun with a big kite and boost high just switch to a foil kite. I'm only 65kg yet my highest jump on my 15m Flysurfer Soul on flat water is 19.5m. Those big air kites are meant to be ridden in small sizes for loop performance, for my weight I usually don't ride any tube kite ...
by kitexpert
Mon Feb 19, 2024 5:31 pm
Forum: Kitesurfing
Topic: Ozone Vortex Ultra-X
Replies: 66
Views: 9245

Re: Ozone Vortex Ultra-X

Mediocre high is perhaps 2/3 at most of what kiter can reach with small(er) kite. One guy I know who has boosted 14.5m from flat water was once able to get over 10m with 17m kite. But he is big 220lbs guy. Normal sized guys, me included, are happy to get 6-8m height with big kites and many times it ...
by kitexpert
Sat Feb 17, 2024 9:00 pm
Forum: Kitesurfing
Topic: Ozone Vortex Ultra-X
Replies: 66
Views: 9245

Re: Ozone Vortex Ultra-X

Disagree [/quote] You really think you can edge as hard as 265lbs guy :D Of course anyone can use big kites but it is just not possible for normal person to boost high or even mediocre high. If wind picks up you can jump much higher using smaller kite. Everyone knows this and reason for it is what ...
by kitexpert
Sat Feb 17, 2024 7:58 pm
Forum: Kitesurfing
Topic: Future Kites-Wings will be around 25 PSI +
Replies: 23
Views: 1882

Re: Future Kites-Wings will be around 25 PSI +

The leading edges should be woven and manufactured like a 3d hose, without sewing, which is the weak spot. But then attaching canopy would be problematic. Also bridle points and valves would need new designs. Woven structure might not be stable enough either. And shape of LE is conical, in two dire...
by kitexpert
Sat Feb 17, 2024 4:45 pm
Forum: Kitesurfing
Topic: Future Kites-Wings will be around 25 PSI +
Replies: 23
Views: 1882

Re: Future Kites-Wings will be around 25 PSI +

What about the torsion though guys? An ultra stiff kite that doesn't turn makes no sense... If strut is thin it won't become ultra stiff. Reducing diameter has much bigger impact on stiffness than new materials. And Aluula being a woven fabric, not a laminate, is not stiff for torsion at all. Getti...

Go to advanced search