Forum for kitesurfers
-
Laughingman
- Very Frequent Poster
- Posts: 2979
- Joined: Mon Mar 16, 2009 4:35 pm
- Local Beach: Kettle Point, Mitchell's Bay, Rondeau Bay
- Favorite Beaches: Kettle Point, Mitchell's Bay, Rondeau Bay, Long Bay, Cayo Guillermo, La Ventana
- Gear: Ocean Rodeo Gen6 Flites 10m, 12m Gen2 Roams 6m and 8m, Cloud D 4.8, 6.2, 8.0, 10.4
Xeon Laluz, Mako Wide 150, Jellyfish Custom surf board quad fin 6', LF Impulse Foil and Kanaha Shapes 37" board
Engine Harness with slider
- Location: Southwestern Ontario
-
Has thanked:
17 times
-
Been thanked:
17 times
Postby Laughingman » Thu Aug 30, 2018 2:58 pm
So these would work I think. Just get one long enough with a short enough thread to cut off and polish the end
https://www.bosunsupplies.com/welded-ey ... -standard/
I would go for the 5" x 5/16Ø with a 2" thread .. then cut off what you don't need and grind the end, polish it and VIOLA! Release pin
Edit... Actually these will be too bulky I just looked at a 5/16 and 3/16 bolt... way to big
-
BWD
- Very Frequent Poster
- Posts: 3849
- Joined: Thu Jun 05, 2003 3:37 am
-
Has thanked:
2 times
-
Been thanked:
81 times
Postby BWD » Sat Sep 01, 2018 1:24 am
3/16 straight terminal works fine for me since 2016.
Trim length a little so you don’t cut fingers on projecting end.
Bends etc are not needed.
-
jaystore
- Frequent Poster
- Posts: 328
- Joined: Thu Jan 28, 2010 9:27 am
- Local Beach: Rome
- Brand Affiliation: JAY
- Location: Rome
-
Has thanked:
0
-
Been thanked:
3 times
-
Contact:
Postby jaystore » Sat Sep 01, 2018 8:17 am
-
tomtom
- Very Frequent Poster
- Posts: 1693
- Joined: Sun Nov 03, 2002 1:00 am
-
Has thanked:
23 times
-
Been thanked:
218 times
Postby tomtom » Sat Sep 01, 2018 10:00 am
BWD wrote: ↑Sat Sep 01, 2018 1:24 am
3/16 straight terminal works fine for me since 2016.
Trim length a little so you don’t cut fingers on projecting end.
Bends etc are not needed.
Could you please link exact type - im still searching - Also maybe whole setup picture.
many thanks!!!
t.
-
tomtom
- Very Frequent Poster
- Posts: 1693
- Joined: Sun Nov 03, 2002 1:00 am
-
Has thanked:
23 times
-
Been thanked:
218 times
Postby tomtom » Sat Sep 01, 2018 11:16 am
Could this be used as primary QR /not leash QR/ - it states its 300kg tested. Also do you DYNABAR - offers this minimalistic setup /just rope with ring/ and tube pin release as package.
I spend some time on your page and there is so many option that im lost. For example - when i buy harness its with spreader bar? And when yes which one?
many thanks.
t.
-
BWD
- Very Frequent Poster
- Posts: 3849
- Joined: Thu Jun 05, 2003 3:37 am
-
Has thanked:
2 times
-
Been thanked:
81 times
Postby BWD » Sat Sep 01, 2018 2:19 pm
tomtom wrote: ↑Sat Sep 01, 2018 10:00 am
BWD wrote: ↑Sat Sep 01, 2018 1:24 am
3/16 straight terminal works fine for me since 2016.
Trim length a little so you don’t cut fingers on projecting end.
Bends etc are not needed.
Could you please link exact type - im still searching - Also maybe whole setup picture.
many thanks!!!
t.
Here is the best picture I have at the moment, it is before I trimmed the length of the pin so t would not stick out so far past the ball:
A similar pin and ball makes up the other half. The setup is detailed in old threads in this website, try “chicken loop bye bye” to start.
The part I used is a Loos cable eye end. Actually size 1/8” or 3mm I believe. Can be found online, example:
https://www.amazon.com/Cableware-EY1-3X ... p_s_a_1_11
Elastic is 1/8” shock cord and balls are nylon, both sourced from a sailing supply store. Ring is 4mm 25mm diameter. Balls around 30mm. Rope used is 4mm amsteel spliced and stitched with v92 polyester.
Setup is cheap and effective.
Keep in mind it is diy and all responsibility for safety and liability is with you.
-
jaystore
- Frequent Poster
- Posts: 328
- Joined: Thu Jan 28, 2010 9:27 am
- Local Beach: Rome
- Brand Affiliation: JAY
- Location: Rome
-
Has thanked:
0
-
Been thanked:
3 times
-
Contact:
Postby jaystore » Sat Sep 01, 2018 7:19 pm
tomtom wrote: ↑Sat Sep 01, 2018 11:16 am
Could this be used as primary QR /not leash QR/ - it states its 300kg tested. Also do you DYNABAR - offers this minimalistic setup /just rope with ring/ and tube pin release as package.
I spend some time on your page and there is so many option that im lost. For example - when i buy harness its with spreader bar? And when yes which one?
many thanks.
t.
Having 3 different Dynabar models you buy harness only and Dynabar you like.
The pin and mushroom handle can be used as primary QR, if you buy the sliding leash you can attach kite depower line to it or we can make a custom system using our low friction sliding ring.
-
jaystore
- Frequent Poster
- Posts: 328
- Joined: Thu Jan 28, 2010 9:27 am
- Local Beach: Rome
- Brand Affiliation: JAY
- Location: Rome
-
Has thanked:
0
-
Been thanked:
3 times
-
Contact:
Postby jaystore » Sat Sep 01, 2018 7:23 pm
tomtom wrote: ↑Sat Sep 01, 2018 11:16 am
Could this be used as primary QR /not leash QR/ - it states its 300kg tested. Also do you DYNABAR - offers this minimalistic setup /just rope with ring/ and tube pin release as package.
I spend some time on your page and there is so many option that im lost. For example - when i buy harness its with spreader bar? And when yes which one?
many thanks.
t.
Having 3 different Dynabar models you buy harness only and Dynabar you like.
The pin and mushroom handle can be used as primary QR, if you buy the sliding leash you can attach kite depower line to it or we can make a custom system using our low friction sliding ring. You can also use 2 (safer) standard ss rings to slide on rope .
Return to “Kitesurfing”
Who is online
Users browsing this forum: Baidu [Spider], Bing [Bot], bittersvolcom, Blackened, Brent NKB, Da Yoda, decay, EscSpace, handy, i_love_storm, jjm, Kuwaiti, Peter_Frank, Regis-de-giens, rickybobbyalex, The line smith, Tiiga, Yahoo [Bot] and 356 guests