Contact   Imprint   Advertising   Guidelines

Moses T40 board - replace the board foil connection from bolt through system to screw in?

Here you can exchange your experience and datas about your home build boards
User avatar
omg
Very Frequent Poster
Posts: 687
Joined: Sun Oct 31, 2004 2:58 pm
Has thanked: 64 times
Been thanked: 17 times

Moses T40 board - replace the board foil connection from bolt through system to screw in?

Postby omg » Wed Apr 12, 2017 3:34 pm

So, I have T40 and otherwise it's nice, BUT it has this annoying system for attaching the foil to the board; first you need to insert the bolt from the top side of the board through the board and then somehow hold the foil in place and then screw in the nut on the bottom side of the foil to the bolt. It's pain in the a$$ to line up everything to get the foil connected to the board. Therefore, I was thinking if it would be possible to drill the holes of the board a bit bigger and put in & epoxy the hexagon connection nuts for each of the four holes, so then you would only need to place the foil over the board and just screw in the bolt from the bottom of the board. Very simple.

The question is, if the board's current holes can be safely drilled to bigger to get the hexagon connection nut in place and if there are any downsides of this operation?

This is what I mean:
Image

Wielandt
Rare Poster
Posts: 44
Joined: Sat May 24, 2014 3:33 pm
Local Beach: Denmark
Favorite Beaches: Holten
Farø
Style: HF,
Gear: Naish Draft, Cabrinha Apollo, Airush Ultra, Storm Voyager, Gong strutless
LFSolo
Moses HF.
Brand Affiliation: None
Has thanked: 0
Been thanked: 1 time

Re: Moses T40 board - replace the board foil connection from bolt through system to screw in?

Postby Wielandt » Wed Apr 12, 2017 3:52 pm

Got the same setup myself. When I connect foil and board I use three smal screwdrivers and put them through board and foil. Then it's all lined up and no problem attaching the first bolt. Just a hint.....

baxterbradford
Medium Poster
Posts: 112
Joined: Wed Aug 05, 2015 3:45 pm
Local Beach: Exmouth, UK
Gear: Foil, surfboard, twintip & 8-18m kites
Brand Affiliation: None
Has thanked: 0
Been thanked: 5 times

Re: Moses T40 board - replace the board foil connection from bolt through system to screw in?

Postby baxterbradford » Wed Apr 12, 2017 5:37 pm

Interesting idea. I've got much quicker at assembling with the supplied fittings. Found lying board & foil on its side works best. I do first one, rotating the capped nut fitting, then others by waiting for click as screw engages. I do them just hand tight. Then once all done, I use Allen key.
Whilst having my board out drying today I noticed in strong sunshine the stringers and plugs around the mounting holes were visible. You might be able to measure the diameter and then decide if the inserts you've found will fit with sufficient material around the outside. No idea what the plug is made from. If you could produce a hexagonal hole as exact fit, then it'd be much stronger.

TomW
Very Frequent Poster
Posts: 3146
Joined: Wed Oct 05, 2005 6:43 pm
Local Beach: Vejbystrand, Habo Ljung, Lomma
Gear: TW Surfboards 5-0
TW Surfboards hydrofoil board 90,105,110cm
Moses Fluente 550/590 + 330/325 and 633 se
Ozone Hyperlink 9mUL, 7m
Hyperlink V2 13m
Concept Air Wave 4,5m
Brand Affiliation: None
Location: Sweden
Has thanked: 29 times
Been thanked: 81 times

Re: Moses T40 board - replace the board foil connection from bolt through system to screw in?

Postby TomW » Wed Apr 19, 2017 8:54 pm

I've keep the strut attached to the board and remove fuselage and wings as a unit. 2 screws.
You need a station wagon.


Return to “Gear Builders”

Who is online

Users browsing this forum: No registered users and 3 guests