Contact   Imprint   Advertising   Guidelines

Pigmenting epoxy

Here you can exchange your experience and datas about your home build boards
RichR2
Medium Poster
Posts: 89
Joined: Thu Aug 10, 2017 12:29 pm
Kiting since: 2000
Gear: Airush Ultra 10m, 8m
Airush Wave 6m
Solo 4,5m
Shinn K2 foil
125cm RR custom
Brand Affiliation: None
Has thanked: 5 times
Been thanked: 4 times

Pigmenting epoxy

Postby RichR2 » Fri Jul 06, 2018 10:48 am

Has anyone used pigments in their laminating epoxy or is it just used for filling/sanding coats and finishing coats as I've heard it affects strength. Thanks

handy
Medium Poster
Posts: 129
Joined: Thu Apr 10, 2008 3:49 pm
Gear: wave
Brand Affiliation: ahcustoms.ch
Has thanked: 0
Been thanked: 9 times
Contact:

Re: Pigmenting epoxy

Postby handy » Fri Jul 06, 2018 1:33 pm

I use pigments (liquid and powder) in most of my boards , no problems with strength at all.

BWD
Very Frequent Poster
Posts: 3709
Joined: Thu Jun 05, 2003 3:37 am
Has thanked: 1 time
Been thanked: 48 times

Re: Pigmenting epoxy

Postby BWD » Fri Jul 06, 2018 8:56 pm

Depending on the pigment you may or may not be able to get opaque color without adding so much pigment strength is affected, especially with thin layers. I think I’ve seen some epoxy pigments that say they are ok for strength at up to 2% volume, if that helps...

TomW
Very Frequent Poster
Posts: 3287
Joined: Wed Oct 05, 2005 6:43 pm
Kiting since: 2001
Local Beach: Vejbystrand, Lomma
Gear: TW Surfboards hydrofoil board 90cm, 110cm
Gong Pro M, 90 cm mast
Ozone Hyperlink 9mUL, 7m
Hyperlink V2 13m
Concept Air Wave 4,5m
Brand Affiliation: None
Location: Sweden
Has thanked: 38 times
Been thanked: 109 times

Re: Pigmenting epoxy

Postby TomW » Sat Jul 07, 2018 6:17 pm

I use pigments, both paste and a tint liquid.
It won't affect strength, it will not be opaque.
There's 2 main approaches:
1. Tint the foam blank before clear laminating.
2. Tint The resin during one or all of laminations.

A few tips:
Mix a small amount of resin Base and pigment, like 20-50ml first and add that to your overall Base and mix well. Then add hardener.

Getting a lam direct onto a unsealed foam blank to be even is an Art. Really difficult.
Seal the blank first and it's likely to be uneven.
So I usually clear lam first, then let that kick and do final lams with tint.

Check swaylocks for tips.

geopeck
Frequent Poster
Posts: 262
Joined: Wed Mar 15, 2006 2:59 pm
Brand Affiliation: None
Location: Homer Ak
Has thanked: 0
Been thanked: 0

Re: Pigmenting epoxy

Postby geopeck » Sat Jul 07, 2018 9:00 pm

I've used the mixol brand tints on some art projects, the colors are so condensed that you couldn't imagine them changing the strength. Like two or three drops to color six oz.

tahoedirk
Frequent Poster
Posts: 216
Joined: Sun Aug 31, 2014 5:02 pm
Local Beach: Kings beach, CA
Favorite Beaches: All clean beaches
Style: out of control
Gear: Homemade gear
Brand Affiliation: None
Has thanked: 0
Been thanked: 0

Re: Pigmenting epoxy

Postby tahoedirk » Thu Aug 02, 2018 4:23 pm

powderized street chalk, construction snap line chalk, pigmented mica powders all work very well. UV resistance is an issue for lighter and brighter colors


Return to “Gear Builders”

Who is online

Users browsing this forum: No registered users and 4 guests