Here you can exchange your experience and datas about your home build boards
-
TomW
- Very Frequent Poster
- Posts: 3585
- Joined: Wed Oct 05, 2005 6:43 pm
- Kiting since: 2001
- Local Beach: Vejbystrand, Lomma
- Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
- Brand Affiliation: None
- Location: Sweden
-
Has thanked:
53 times
-
Been thanked:
193 times
Postby TomW » Sun Nov 25, 2018 1:47 pm
I was making a surf/foil convertible and split board, but changed my mind and cut the blank down to a 105 Pocket.
Might still make it split, but debating if I can somehow get it into a bag with mast and wings and check it in on flights as regular bag.
-
plummet
- Very Frequent Poster
- Posts: 6819
- Joined: Sat Aug 29, 2009 11:25 pm
- Local Beach: EE
- Favorite Beaches: NZ
- Style: Terrain riding
- Gear: Old wornout ozone.
Plummet hydrofoil and mutant
- Brand Affiliation: None
-
Has thanked:
11 times
-
Been thanked:
224 times
Postby plummet » Sun Nov 25, 2018 5:58 pm
What's the cut out for? Looks like a skate board deck
-
tmcfarla
- Frequent Poster
- Posts: 447
- Joined: Sun Apr 16, 2006 6:35 am
-
Has thanked:
9 times
-
Been thanked:
54 times
Postby tmcfarla » Sun Nov 25, 2018 8:16 pm
If you make it a bit smaller, you should be able to check it in on flights. In the states at least, airlines allow 62 linear inches (sum of length, width, and height). 5 inches in height is the minimum you can get away with if you want to fit a mast in the same bag. That leaves 57 inches for height plus width (145 cm). My everyday board is 43x17.5 inches (109x44 cm). I could easily bring width down to 16 inches. Bringing length down is harder, but since it is already too short to handle any touch downs, I think 40 inches would be ok. 40x16 inches (and 5 inch height for mast) leaves an inch of grace for the bag. That is about 101.5x40.5 cm. Small for sure, but not much smaller than my board, and much easier to travel with.
-
TomW
- Very Frequent Poster
- Posts: 3585
- Joined: Wed Oct 05, 2005 6:43 pm
- Kiting since: 2001
- Local Beach: Vejbystrand, Lomma
- Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
- Brand Affiliation: None
- Location: Sweden
-
Has thanked:
53 times
-
Been thanked:
193 times
Postby TomW » Tue Nov 27, 2018 10:57 pm
I've looked at my stance and foot position on photos of me on my 120 cm board. Photos taken with line mount. This tells me I can cut 50mm from the tail and 250 from nose and still have plenty of room. So I'm cutting it down even more.
So the board will be 90*45*3,5. My mast is 93cm with a 140mm wide plate.
I found a company in UK that will make a bag for me at a reasonable price. Bag will have outside dimension 95*47*16 = 158cm which is common restriction.
The mast will lay on top of board with plate hanging off the tail.
I'll be able to get my 9 and 7 Hyperlink, wings, fuselage, board short harness, bar, shorty wetsuit in the bag. That's what I need to get in.
Other stuff like helmet, clothes etc I can take carry-on. Normally travel to warm places.
-
TomW
- Very Frequent Poster
- Posts: 3585
- Joined: Wed Oct 05, 2005 6:43 pm
- Kiting since: 2001
- Local Beach: Vejbystrand, Lomma
- Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
- Brand Affiliation: None
- Location: Sweden
-
Has thanked:
53 times
-
Been thanked:
193 times
Postby TomW » Tue Nov 27, 2018 11:00 pm
plummet wrote: ↑Sun Nov 25, 2018 5:58 pm
What's the cut out for? Looks like a skate board deck
You mean the dark foam inlay? That's HD foam. I started with a 135 surf/ foil convertible. Changed my mind to do only foilboard 105cm. Cut it down. Now decided I'll do 90cm board for compact travel. So I'll cut more off...
-
plummet
- Very Frequent Poster
- Posts: 6819
- Joined: Sat Aug 29, 2009 11:25 pm
- Local Beach: EE
- Favorite Beaches: NZ
- Style: Terrain riding
- Gear: Old wornout ozone.
Plummet hydrofoil and mutant
- Brand Affiliation: None
-
Has thanked:
11 times
-
Been thanked:
224 times
Postby plummet » Wed Nov 28, 2018 3:08 am
TomW wrote: ↑Tue Nov 27, 2018 11:00 pm
plummet wrote: ↑Sun Nov 25, 2018 5:58 pm
What's the cut out for? Looks like a skate board deck
You mean the dark foam inlay? That's HD foam. I started with a 135 surf/ foil convertible. Changed my mind to do only foilboard 105cm. Cut it down. Now decided I'll do 90cm board for compact travel. So I'll cut more off...
No, The cut outs on the side of the board.
-
max
- Very Frequent Poster
- Posts: 654
- Joined: Thu Aug 01, 2002 1:00 am
-
Has thanked:
9 times
-
Been thanked:
11 times
Postby max » Wed Nov 28, 2018 8:54 am
TomW wrote: ↑Tue Nov 27, 2018 10:57 pm
I've looked at my stance and foot position on photos of me on my 120 cm board. Photos taken with line mount. This tells me I can cut 50mm from the tail and 250 from nose and still have plenty of room. So I'm cutting it down even more.
So the board will be 90*45*3,5. My mast is 93cm with a 140mm wide plate.
I found a company in UK that will make a bag for me at a reasonable price. Bag will have outside dimension 95*47*16 = 158cm which is common restriction.
The mast will lay on top of board with plate hanging off the tail.
I'll be able to get my 9 and 7 Hyperlink, wings, fuselage, board short harness, bar, shorty wetsuit in the bag. That's what I need to get in.
Other stuff like helmet, clothes etc I can take carry-on. Normally travel to warm places.
hey Tom . . . how much scoop/rocker would you have had on the 120 . . . and now will have on the 90cm?
-
TomW
- Very Frequent Poster
- Posts: 3585
- Joined: Wed Oct 05, 2005 6:43 pm
- Kiting since: 2001
- Local Beach: Vejbystrand, Lomma
- Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
- Brand Affiliation: None
- Location: Sweden
-
Has thanked:
53 times
-
Been thanked:
193 times
Postby TomW » Wed Nov 28, 2018 7:59 pm
Plummet the last pick is before I cut off the tail.
Max, I have about 90mm nose rocker on my 135, 120, and this one , I'll cut tail down so nose rocker unchanged. Might take 10-20mm off nose.
-
Bletti
- Frequent Poster
- Posts: 376
- Joined: Thu Feb 26, 2015 9:13 am
- Gear: Slingshot Rally 10m
- Brand Affiliation: None
-
Has thanked:
1 time
-
Been thanked:
0
Postby Bletti » Thu Nov 29, 2018 3:55 am
Looks good. Great idea. I might look for a damaged blank to shape down for a pocketboard myself. I was thinking of doing a divinicell core but this could be cheaper.
Please post more photos as you build. I'm curious how you'll reinforce the bolt holes and how light it ends up being.
-
AndersP
- Frequent Poster
- Posts: 274
- Joined: Mon Jul 03, 2017 9:23 pm
- Gear: Foil and Mutant
- Brand Affiliation: None
- Location: Goteborg
-
Has thanked:
63 times
-
Been thanked:
56 times
Postby AndersP » Thu Nov 29, 2018 10:43 am
A shape that looks something like this would probably be the most travel friendly outline. It's maybe a bit to big with 106x43cm dimensions. The weight must also be a travellers dream at 1.5kg or 2.7kg complete with foil!
The hard thing for this combo will be how to fit the
mast-fuselage in a bag.
Return to “Gear Builders”
Who is online
Users browsing this forum: Bing [Bot] and 329 guests