Contact   Imprint   Advertising   Guidelines

DIY pocket foil board buoyancy

Here you can exchange your experience and datas about your home build boards
Matthijs94
Rare Poster
Posts: 1
Joined: Tue Jul 07, 2020 2:11 pm
Kiting since: 2007
Gear: Cabrinha FX 7, 9, 12
Twintip
Surfboard
Slingshot foil
Brand Affiliation: None
Has thanked: 2 times
Been thanked: 0

DIY pocket foil board buoyancy

Postby Matthijs94 » Tue Jul 07, 2020 2:57 pm

Last weekend I made a pocket foil board. Two plates of 6mm poplar plywood with reinforcement (meranti plywood 18mm thick) at the baseplate. Dimensions 90x45x1.2cm (with reinforcement 2.4cm thick). In between the poplar and meranti I placed 4 inserts with a big plate (80x30mm). Total weight of the board 2.4kg. Planning to give it 4 layers of fiberglass 200g, 2 on top, 2 at the bottom. Which gives it a roughly total weight of 3.4kg. The structure is strong enough in my opinion. Only thing I am not sure about is the buoyancy. I am riding a Slingshot hover glide NF2, which is not light at all (5.4kg - 11.9lbs). Still need to add deck grip, which also adds some extra volume.

Any experience with adding some volume? I saw spherecore, which adds volume, any experience with that material?
WhatsApp Image 2020-07-07 at 14.56.59.jpeg
Attachments
WhatsApp Image 2020-07-07 at 15.54.21.jpeg
WhatsApp Image 2020-07-07 at 15.35.49.jpeg
WhatsApp Image 2020-07-07 at 15.35.49 (1).jpeg

TomW
Very Frequent Poster
Posts: 3436
Joined: Wed Oct 05, 2005 6:43 pm
Kiting since: 2001
Local Beach: Vejbystrand, Lomma
Gear: TW Surfboards hydrofoil board 90cm, 110cm
Gong Pro M, 90 cm mast
Ozone Hyperlink 9mUL, 7m
Hyperlink V2 13m
Concept Air Wave 4,5m
Brand Affiliation: None
Location: Sweden
Has thanked: 44 times
Been thanked: 145 times

Re: DIY pocket foil board buoyancy

Postby TomW » Tue Jul 07, 2020 4:33 pm

Best way is to put eps or 30 kg PU foam between. 10-20mm thick. Then embed the reinforcement for foil in between the ply skins. That core you show will suck up a ton of resin and add almost no flotation.
You can buy 10mm PU foam in smaller pieces and have it in several pieces, it doesn't have to be in one sheet. Easycomposites.co.uk
These users thanked the author TomW for the post:
Matthijs94 (Tue Jul 07, 2020 7:47 pm)
Rating: 8.33%

merl
Frequent Poster
Posts: 367
Joined: Tue May 15, 2007 8:43 pm
Kiting since: 1999
Gear: Mixed, flysurfer peak, concept air pulsion, wave & firefly, various LEIs. Mostly HF these days.
Brand Affiliation: None
Location: Sweden
Has thanked: 47 times
Been thanked: 26 times

Re: DIY pocket foil board buoyancy

Postby merl » Tue Jul 07, 2020 5:35 pm

I can't see why you would need so much glass on a plywood board. Can you test the stiffness? I recon it will be stiff enough without any glass. If stiff enough then just coat it with epoxy for waterproofing. If not, just stiffen the center with some 200g and then coar the whole thing in the lightest cloth you can get. If you add low density foam to both sides then you will need glass for impact resistance, but the amount you need will depend on how soft the foam is.

(I'm no expert but have messed around with plenty of plywood, foam, epoxy etc.)
These users thanked the author merl for the post:
Matthijs94 (Tue Jul 07, 2020 7:47 pm)
Rating: 8.33%


Return to “Gear Builders”

Who is online

Users browsing this forum: No registered users and 2 guests