Contact   Imprint   Advertising   Guidelines

How to make 4:1 Trim System on 2020 North Navigator Bar

Here you can exchange your experience and datas about your home build boards
User avatar
JimmyRyder
Rare Poster
Posts: 44
Joined: Wed Jun 27, 2012 10:36 am
Kiting since: 2012
Weight: 220
Local Beach: Atlanta - GA
Ocean Side - GA, SC, NC
Tampa - FL
Favorite Beaches: Tampa - USA
Cape Hatteras - USA
Charleston - USA
Tarifa - Spain
Lefkada - Greece
Rhodos - Greece
Gokceada - Turkey
Urla - Turkey
Alacati - Turkey
Cesme - Turkey
Soma Bay - Egypt
Elgouna - Egypt
Marsala - Italy
Mamaia - Romania
Sulina - Romania
Style: FreeRide; Snowkiting;
Gear: 2020 North - REACH - 10m
2020 Liquid Force - NV - 13.5m
2019 Liquid Force - SOLO - 15.5m

2020 Liquid Force - ABSOLUTE - 140cm
2020 Liquid Force - POD 4'4 - HydroBoard
2020 Liquid Force - IMPULSE - Hydrofoil
2020 Liquid Force - MESSENGER - Surfboard
Brand Affiliation: None
Location: Atlanta / Tampa
Has thanked: 21 times
Been thanked: 2 times

How to make 4:1 Trim System on 2020 North Navigator Bar

Postby JimmyRyder » Sun Sep 06, 2020 6:50 am

Hello guys,

I've been riding different bars throughout the years from Ozone to Sling, Cab, Airush, etc.

The easiest to trim were the Core (has a 4:1 ratio) and some other custom race-bars (also 4:1 ratio).

So on my new
2020 NORTH gear I would like to turn the Trimming System into a 4:1 on my new Navigator bar.

I know that beside the existing parts the bar is made of, I will need an extra
longer line and one Slider.

The new Longer-Line and the Trimming Line will both be connected from the Loop on top end of the Depower Line (right at the cleat).

1) LONGER LINE (new line) - goes all the way through the Front Lines SWIVEL and back down - then the looped end will connect to a SLIDER.

2) TRIMMING LINE - will go through the SLIDER above mentioned line, then come down and through the CLEAT.

My questions are:

a) What type of line to use for the longer line (dynema, spectra, etc) ?!

b) What thickness should this line have ?! (obviously I prefer thinner but strong) :D

c) How long should this line be in order to not screw up the bar setting ?!

d) I know the Leader Lines should be replaced with longer once - How long should those be ?!

Thanks in advance for your input and help !!! :jump:

(this topic is addressed mainly to the Racers that actually did and know this bar setting please)
Last edited by JimmyRyder on Sun Sep 06, 2020 3:16 pm, edited 1 time in total.

Herman
Very Frequent Poster
Posts: 762
Joined: Tue Jun 04, 2019 7:09 pm
Style: My Own.
Gear: SLE, foils and C kites, TTs, Directionals, Landboards, Buggy.
Brand Affiliation: None
Has thanked: 73 times
Been thanked: 173 times

Re: How to make 4:1 Trim System on 2020 North Navigator Bar

Postby Herman » Sun Sep 06, 2020 10:40 am

You only need to extend the rear leaders if you want a bigger trim range or if you are going to use a floating single pulley rather than fixed double pulley. Line required is dependent on cleat to be used, length is trim X no of runs plus desired handle (+ allowance for splice or knots).

The difference between a 12in pizza and the average pro kitesurfer?

A 12in pizza can feed a family of four!
These users thanked the author Herman for the post:
JimmyRyder (Sun Sep 06, 2020 3:15 pm)
Rating: 8.33%


Return to “Gear Builders”

Who is online

Users browsing this forum: No registered users and 2 guests