Here you can exchange your experience and datas about your home build boards
-
JimmyRyder
- Rare Poster
- Posts: 44
- Joined: Wed Jun 27, 2012 10:36 am
- Kiting since: 2012
- Weight: 220
- Local Beach: Atlanta - GA
Ocean Side - GA, SC, NC
Tampa - FL
- Favorite Beaches: Tampa - USA
Cape Hatteras - USA
Charleston - USA
Tarifa - Spain
Lefkada - Greece
Rhodos - Greece
Gokceada - Turkey
Urla - Turkey
Alacati - Turkey
Cesme - Turkey
Soma Bay - Egypt
Elgouna - Egypt
Marsala - Italy
Mamaia - Romania
Sulina - Romania
- Style: FreeRide; Snowkiting;
- Gear: 2020 North - REACH - 10m
2020 Liquid Force - NV - 13.5m
2019 Liquid Force - SOLO - 15.5m
2020 Liquid Force - ABSOLUTE - 140cm
2020 Liquid Force - POD 4'4 - HydroBoard
2020 Liquid Force - IMPULSE - Hydrofoil
2020 Liquid Force - MESSENGER - Surfboard
- Brand Affiliation: None
- Location: Atlanta / Tampa
-
Has thanked:
21 times
-
Been thanked:
2 times
Postby JimmyRyder » Sun Sep 06, 2020 6:50 am
Hello guys,
I've been riding different bars throughout the years from Ozone to Sling, Cab, Airush, etc.
The easiest to trim were the Core (has a 4:1 ratio) and some other custom race-bars (also 4:1 ratio).
So on my new 2020 NORTH gear I would like to turn the Trimming System into a 4:1 on my new Navigator bar.
I know that beside the existing parts the bar is made of, I will need an extra longer line and one Slider.
The new Longer-Line and the Trimming Line will both be connected from the Loop on top end of the Depower Line (right at the cleat).
1)
LONGER LINE (new line)
- goes all the way through the Front Lines SWIVEL and back down - then the looped end will connect to a SLIDER.
2)
TRIMMING LINE - will go through the SLIDER above mentioned line, then come down and through the CLEAT.
My questions are:
a) What type of line to use for the longer line (dynema, spectra, etc) ?!
b) What thickness should this line have ?! (obviously I prefer thinner but strong)
c) How long should this line be in order to not screw up the bar setting ?!
d) I know the Leader Lines should be replaced with longer once - How long should those be ?!
Thanks in advance for your input and help !!!
(this topic is addressed mainly to the Racers that actually did and know this bar setting please)
Last edited by
JimmyRyder on Sun Sep 06, 2020 3:16 pm, edited 1 time in total.
-
Herman
- Very Frequent Poster
- Posts: 2095
- Joined: Tue Jun 04, 2019 7:09 pm
- Style: My Own.
- Gear: SLE, foils and C kites, TTs, Directionals, Landboards, Buggy.
- Brand Affiliation: None
-
Has thanked:
218 times
-
Been thanked:
529 times
Postby Herman » Sun Sep 06, 2020 10:40 am
You only need to extend the rear leaders if you want a bigger trim range or if you are going to use a floating single pulley rather than fixed double pulley. Line required is dependent on cleat to be used, length is trim X no of runs plus desired handle (+ allowance for splice or knots).
The difference between a 12in pizza and the average pro kitesurfer?
A 12in pizza can feed a family of four!
- These users thanked the author Herman for the post:
- JimmyRyder (Sun Sep 06, 2020 3:15 pm)
Return to “Gear Builders”
Who is online
Users browsing this forum: No registered users and 151 guests