Contact   Imprint   Advertising   Guidelines

Screws stripping out on the Slingshot Hoverglide NF2?

A forum dedicated to Hydrofoil riders
beebad
Medium Poster
Posts: 156
Joined: Mon May 23, 2016 2:44 pm
Kiting since: 0
Local Beach: Chesapeak, Triton, Mayo, Rehobeth bay, dewey bch,OBX
Favorite Beaches: South Padre Island, Mirlo Beach-NC,
Style: Freeride
Gear: 7m, 9m, 12m Cabrinha Switchblades, 15 Contra, Cabrinha 148 Spectrum, 137 ACE, Litewave Dave WING, Ugo, GP6B, slingshot hoverglide nf2 foil-35",15"24" masts, slingshot dwarfcraft 54" foilboard
Brand Affiliation: None
Location: Kent Island
Has thanked: 16 times
Been thanked: 0

Screws stripping out on the Slingshot Hoverglide NF2?

Postby beebad » Sat Jan 26, 2019 6:08 pm

A friend of mine cautioned me about the hardware on this foil I just got in the mail!

HAs anyone seen any hardware failures with this foil?

Thanks

ap888
Frequent Poster
Posts: 209
Joined: Thu Sep 13, 2018 2:24 am
Kiting since: 2007
Local Beach: Zion/K peir/Inver/Goderich
Favorite Beaches: Good wind/Flat water/Good waves
Style: Foil/Loops/Big Air/Strapless
Gear: Ozone Uno V2 4m
North Neo (17) 5m
Cabrinha Drifter (16) 8m
Flysurfer Sonic 2 -11m
Slingshot Hoverglide
BWS Stallion 5’
CrazyFly Shox Custom 135
Groove Skate
Ride Engine
Brand Affiliation: None
Has thanked: 3 times
Been thanked: 3 times

Re: Screws stripping out on the Slingshot Hoverglide NF2?

Postby ap888 » Sat Jan 26, 2019 7:14 pm

Have a HoverglideNF2 used for 2 seasons and the bolts that connect fuselage to mast are getting loose ish (loosing tolerance) from taking them out every session always made sure not a spec of sand was on bolts or inserts to minimize loosing tolerance... would imagine all foils do this after time ?...but luckily only ride fresh water... so loaded them up with medium strength lock tight so can still come out in future if needed but haven’t came loose since then :D So your good for 2 years anyways :)

juandesooka
Very Frequent Poster
Posts: 891
Joined: Wed Aug 29, 2012 8:05 pm
Kiting since: 2011
Local Beach: Sooke, BC, Canada
Gear: BWS / Ocean Rodeo / Stringy Foil
Brand Affiliation: None
Has thanked: 3 times
Been thanked: 9 times

Re: Screws stripping out on the Slingshot Hoverglide NF2?

Postby juandesooka » Sat Jan 26, 2019 7:35 pm

I have just experienced loosening bolts on sup wing. From wipe outs in over large surf....widened the channel the mast slides into. I am told by others too that nonpermanent blue loctite is the answer.

Other side of this equation. ...slime up your bolts with tefgel and periodically re apply so they don't become permanently bonded.


Return to “Hydrofoil”

Who is online

Users browsing this forum: DAnderson, drsurf, jaros, mmac, neilhapgood, Surfkiternew and 7 guests

cron