Contact   Imprint   Advertising   Guidelines

Moses Silente + Onda 683S + 483

A forum dedicated to Hydrofoil riders
dan_kan
Rare Poster
Posts: 4
Joined: Sat Feb 23, 2019 5:28 pm
Kiting since: 8
Local Beach: Poland, Gdansk, Rewa
Favorite Beaches: Rewa, Kuznica
Style: foil
Gear: Minimabeta 11m2, Moses Silente + Onda 683
Brand Affiliation: None
Has thanked: 2 times
Been thanked: 1 time

Moses Silente + Onda 683S + 483

Postby dan_kan » Sat Feb 23, 2019 6:18 pm

Hi,
Maybe someone will benefit from this conversion.
I designed and tested the Moses Silente foil adapters for the Onda 683 and 483 wings.
The profile has been developed assuming that the assembly screws connecting the wings 683 and 483 with the original keel are perfectly vertical. To check the assumption itself, without waiting for a casting of resin, I printed with PETG 100% fill, mounted and .. works :o
I did not even have to move my foil nearer to the stern, and by default it is set to the right up to the front (I hold the rear foot in front of the strap)
It flies great, although some shuttlecocks were humming, so I will need to treat them with water paper.
Wing spacing went 70cm, originally ~ 75cm, but the front wing is mounted in Silente closer to the foil, so the rear, which is the "counterbalance", can also be closer.
Comparative picture - thanks to other user Piotrbyku:
49696221_381896609054046_6181392107215781888_n.jpg
stl files and pictures for 683 and 483:
https://drive.google.com/open?id=1zjAYW ... F1UmT7hmpm
683:
683.PNG
20190223_161914.jpg
From the left (all conical screws)
1) 6x20mm, original 6 corner nut from Moses, ground to 12.5mm width
2) 6x20mm,
3) 6x35mm, passes through the wing and adapter so you should not lose your wing
4) 6x20mm,
5) 6x20mm, original nut 6 angled from Moses
6) 6x25mm

483:
483rear2.JPG
20190223_161316.jpg
From the stern
1) 6x14mm, 6-point cap, gr. 3mm
2) 6x25mm, passes through the wing and adapter
3) 6x20mm
20190126_190434.jpg
Printing the adapter:
PETG, fill 100%, for me 230oC, table 80oC, 0.2mm
(PLA is stiffer but more fragile and not resistant to UV, ABS is too soft for me)
PETG treats as a transitional stage, I ultimately want to make resin castings, and if someone has access and the ability to make aluminum components, just envy: roll:
These users thanked the author dan_kan for the post:
BraCuru (Sun Feb 24, 2019 12:21 pm)
Rating: 10%

grigorib
Very Frequent Poster
Posts: 1353
Joined: Mon Aug 01, 2016 8:12 pm
Kiting since: 2009
Local Beach: Clinton Lake, IL; Lake Michigan; Tawas, MI; OBX; SPI
Gear: Kites: Slingshot Rally 5/7/9/11m, Slingshot Turbine 9m, Flysurfer Speed4 10m, Peter Lynn Venom II ARC 16m
Boards: Spleene RIP 37, Flysurfer Flydoor5 XL, Slingshot/Moses 91cm/42” masts 590/633 wings, Slingshot Dwarfcraft 42", MBS Comp 95x

For sale: Slingshot Coupe 6'
Brand Affiliation: None
Has thanked: 21 times
Been thanked: 29 times

Re: Moses Silente + Onda 683S + 483

Postby grigorib » Sat Feb 23, 2019 8:32 pm

Looks awesome!
Imagine how much money you can make making an adapter to mount 633 to 647/680 fuselage
These users thanked the author grigorib for the post:
dan_kan (Sat Feb 23, 2019 10:53 pm)
Rating: 10%

User avatar
NYKiter
Very Frequent Poster
Posts: 1860
Joined: Fri Mar 22, 2013 9:17 pm
Kiting since: 2010
Style: Wave
Gear: .
Has thanked: 0
Been thanked: 3 times

Re: Moses Silente + Onda 683S + 483

Postby NYKiter » Sat Feb 23, 2019 11:31 pm

NICE WORK!

You could use your prints as a pattern and try your hand at alum casting...get a little propane foundry and crucible and your off.

Im not so sure the 647/680 fuselage is a good candidate for a 633 wing adapter....the concave is a lot smaller and the nose is much shorter....


Return to “Hydrofoil”

Who is online

Users browsing this forum: No registered users and 6 guests

cron