Contact   Imprint   Advertising   Guidelines

Harness with Sliding spreader bar

Forum for kitesurfers
DAnderson
Medium Poster
Posts: 85
Joined: Thu Aug 25, 2016 2:17 pm
Kiting since: 2015
Local Beach: SWFL
Gear: red T-38, 633, 720, 637, 590, 483, 420, 330
12m soul, 12/9/7 sst, 9/7/5 turbine
Brand Affiliation: None
Has thanked: 5 times
Been thanked: 7 times

Re: Harness with Sliding spreader bar

Postby DAnderson » Tue Jan 15, 2019 4:03 pm

I had the rope snap on my Dynabar. Replaced w/ 5mm upgraded line & 8,900# line has held up much better.
https://www.westmarine.com/buy/new-engl ... e=11633112

juandesooka
Very Frequent Poster
Posts: 1019
Joined: Wed Aug 29, 2012 8:05 pm
Kiting since: 2011
Local Beach: Sooke, BC, Canada
Style: Canada's Kai Lenny (in my mind)
Gear: Ocean Rodeo / Stringy Foil / Slingshot Surf Foil
Brand Affiliation: Open to offers
Has thanked: 34 times
Been thanked: 36 times

Re: Harness with Sliding spreader bar

Postby juandesooka » Tue Jan 15, 2019 7:21 pm

juandesooka wrote:
Tue Jan 15, 2019 12:59 am
Replace your rope often! And don't buy the Ride Engine replacement -- it's the same foot long piece of dyneema you get at the boat store.
One more thing to add to this: if you have dynabar, their replacement rope is maybe worth a little extra money. They have braided a loop in one end (which activates the pin quick release for the rope) and then bury the tail of the braid across the entire length of the rope. So their rope feels quite a bit "beefier", in effect it is two strands of dyneema in one.

kiteswede
Medium Poster
Posts: 63
Joined: Mon Oct 29, 2018 1:41 pm
Kiting since: 0
Local Beach: Göteborg
Gear: F-one kite
Brand Affiliation: None
Has thanked: 20 times
Been thanked: 5 times

Re: Harness with Sliding spreader bar

Postby kiteswede » Tue Jan 15, 2019 7:35 pm

my only concern wiht the slider bar, is the rope snapping. Seems like this happens quite a bit.

Any thoughts?
[/quote]

Manera got two ropes in their bar. And you change them when they start to wear out. :)

or6
Frequent Poster
Posts: 413
Joined: Fri Mar 25, 2016 3:29 pm
Kiting since: 1998
Local Beach: Wijk aan zee, Zandmotor, Hoek
Favorite Beaches: Muriwai NZ, El Medano Tenerife, la Ventana México, Hood River, Portland area, Vancouver Island, Wijk aan Zee, Moulay Bouzerktoun
Style: Waveriding, strictly strapless, some TT,
Gear: RRD Religion 4, 5, 6, 7, 8 and 9, Appletree Klokhouse Noseless 5'3", Shinn Bronq
Brand Affiliation: None
Has thanked: 36 times
Been thanked: 21 times

Re: Harness with Sliding spreader bar

Postby or6 » Wed Jan 16, 2019 9:05 pm

Well, I can only speak for my RideEngine harness. I have replaced the rope two or three times...you just pay attention and replace when necessary. Ordinary 6 mm Dyneema...not too expensive.

If breaking it really worries you, you can use a secondary rope. Howz depends on your harness of choice.

User avatar
IBaKiteboarder
Medium Poster
Posts: 69
Joined: Sat Jan 14, 2017 3:55 am
Kiting since: 2015
Local Beach: Emerald Isle, Indian Beach (thus "IB" a Kiteboarder), Bogue Sound, Cape Lookout, all in NC
Style: Upright
Gear: Slingshot Rally 7-9-12, Turbine 15
Misfit 136, 146
Brand Affiliation: None
Has thanked: 0
Been thanked: 1 time
Contact:

Re: Harness with Sliding spreader bar

Postby IBaKiteboarder » Wed Jan 16, 2019 10:57 pm

I used the SS Talon on my slider bar for the first time 2 weeks ago and so far think it's awesome. It brings the bar a lot closer than having a long chicken loop stretched out which avoids reach problems, especially when getting overpowered and trying to sheet out... we've all seen people trying to stretch and lean as much as possible to dump power, and with this set-up it's easy. I also feel like I can lean back into my harness more without stretching to reach the bar while riding. Here's a pic of how it looks...
Attachments
GOPR0218_Moment.jpg
These users thanked the author IBaKiteboarder for the post:
granit02 (Mon Jan 21, 2019 10:51 am)
Rating: 10%

Alysum
Medium Poster
Posts: 150
Joined: Tue Mar 10, 2015 11:28 pm
Kiting since: 2014
Gear: a kite
Brand Affiliation: None
Location: France
Has thanked: 0
Been thanked: 0

Re: Harness with Sliding spreader bar

Postby Alysum » Sun Jan 20, 2019 7:24 am

I have the Dakine Nitrous shorts and I run my own line with a shackle. I use it for strapless but use the hook for foil and strong winds. I've had the rope and also the chicken loop snap...

I need to replace my old shorts and I can only get the Ion B2 shorts. Unfortunately it's not possible to rig my own slider rope, so looking for recommendations on how to have both the hook and rope.

User avatar
mr_daruman
Frequent Poster
Posts: 277
Joined: Thu Feb 19, 2009 1:33 pm
Kiting since: 2002
Local Beach: Okinawa beaches
Favorite Beaches: Mauritius
New Caledonia
Canaries
Style: Surfkite
Gear: Switch
Ozone
Wainman Hawaii
Brand Affiliation: Jimmy Lewis, Infinity
Location: Japan
Has thanked: 0
Been thanked: 5 times

Re: Harness with Sliding spreader bar

Postby mr_daruman » Mon Jan 21, 2019 3:54 am

Sliding rope is great when riding toeside, enable easier movement.
Instead of the thin rope rings provided I like to replace with a wide non abrasive ring used for boat ropes.

In case the rope snaps ( in 3 years, happened 1 time because a a bad knot) I always tie below a second « emergency » rope just incase (works very easy with ride engine harnesses)
Or have a second short leash tied to the back of the harness ready to quickly clip to the front using rings I have on both sides of the straps.
1B9C92AA-1FB5-408B-AB0F-D198CCF84790.jpeg

daminou
Rare Poster
Posts: 2
Joined: Sat May 18, 2019 8:03 pm
Kiting since: 2017
Local Beach: Ocean Beach, San Francisco
Favorite Beaches: Waddell Creek, CA
Kanaha Maui
Style: Wave
Gear: SST
Brand Affiliation: None
Has thanked: 0
Been thanked: 0

Re: Harness with Sliding spreader bar

Postby daminou » Sat May 18, 2019 8:10 pm

Onda wrote:
Mon Jan 07, 2019 10:51 am
Best I´ve ever experienced is:
Carbon spreader bar (rideengine 2016 model) with rope plus a Ronstan Orbit 20 block connected to a Cabrinha Fireball Bar´s QR (without the original Fireball piece).
Totally friction-less, super-smooth movement with minimal distance between the rope and the quick release. You don´t even notice that something is sliding along the rope.
Very simple setup with hardly any metal parts that can fail / corrode.

Before I used a conventional PU chicken loop directly connected to the rope. Fine at the beginning. But the PU material becomes "rough" after some hours of use, resulting in "sticking" on the rope and very uncomfortable jerking movement along the rope. Not good.

Doesn´t matter which harness, actually. As long as you can knot in a rope somewhere at two points.
I am really interested in the Cabrinha Fireball Bars QR (without the original Fireball piece). My concern of is that it would be impossible to put back in the water to relaunch after you release (when the kite falls in the waves). What do you think? Are you able to relaunch after you release? It is doable with a regular chicken loop and I find it quite convenient.

I am thinking there is actually the exact same problem with the Fireball setup.

knotwindy
Very Frequent Poster
Posts: 1509
Joined: Mon Sep 26, 2011 4:49 am
Kiting since: 2007
Local Beach: baja, gorge
Style: erratic to none
Gear: yes, I use gear
Brand Affiliation: None
Has thanked: 49 times
Been thanked: 46 times

Re: Harness with Sliding spreader bar

Postby knotwindy » Sun May 19, 2019 2:42 am

How often does that happen? If it’s just rarely, bring a carabiner and use it just to get back to shore and reset. If it’s all the time, what are you doing?

User avatar
cglazier
Very Frequent Poster
Posts: 2460
Joined: Sat Apr 13, 2002 1:00 am
Kiting since: 1999
Gear: Naish, Duotone, Flysurfer, Alpine
Brand Affiliation: None
Location: Vancouver, Canada
Has thanked: 28 times
Been thanked: 32 times

Re: Harness with Sliding spreader bar

Postby cglazier » Mon May 20, 2019 2:46 am

Here is the new 2019 Ion rope spreader bar. It is clean and simple and has an adjustable rope. I am using it with my Dakine harness and it works well.

:wink: CG
IMG_2066.jpg
IMG_2066.jpg (45.02 KiB) Viewed 428 times


Return to “Kitesurfing”

Who is online

Users browsing this forum: Bing [Bot], Google [Bot], jumptheshark, mike dubs, MSN [Bot], newold86 and 16 guests

cron