Here you can exchange your experience and datas about your home build boards
-
plummet
- Very Frequent Poster
- Posts: 6819
- Joined: Sat Aug 29, 2009 11:25 pm
- Local Beach: EE
- Favorite Beaches: NZ
- Style: Terrain riding
- Gear: Old wornout ozone.
Plummet hydrofoil and mutant
- Brand Affiliation: None
-
Has thanked:
11 times
-
Been thanked:
224 times
Postby plummet » Sat Jul 27, 2019 8:28 pm
Hey bro's
Anyone got a handle on what the latest TT fin toe in angles are?
I'm currently sitting at 1.5°. I'm thinking that might be a little shallow.
-
plummet
- Very Frequent Poster
- Posts: 6819
- Joined: Sat Aug 29, 2009 11:25 pm
- Local Beach: EE
- Favorite Beaches: NZ
- Style: Terrain riding
- Gear: Old wornout ozone.
Plummet hydrofoil and mutant
- Brand Affiliation: None
-
Has thanked:
11 times
-
Been thanked:
224 times
Postby plummet » Thu Aug 01, 2019 6:31 pm
Well?
-
BWD
- Very Frequent Poster
- Posts: 3849
- Joined: Thu Jun 05, 2003 3:37 am
-
Has thanked:
2 times
-
Been thanked:
81 times
Postby BWD » Thu Aug 01, 2019 7:25 pm
I have only tried "straight" and "a little", never measured degrees. couldn't tell a difference, but the boards were different anyway.
You could make the aft hole a bit oval sideways and experiment, then fill in to your preference I guess...
With surf fins on kiteboards I tend to go with rear of futures boxes about 3-4mm wider spread than the fronts, a little straighter than most normal surfboards.
Quad rears I run straight, no toe in. YMMV
-
plummet
- Very Frequent Poster
- Posts: 6819
- Joined: Sat Aug 29, 2009 11:25 pm
- Local Beach: EE
- Favorite Beaches: NZ
- Style: Terrain riding
- Gear: Old wornout ozone.
Plummet hydrofoil and mutant
- Brand Affiliation: None
-
Has thanked:
11 times
-
Been thanked:
224 times
Postby plummet » Thu Aug 01, 2019 11:38 pm
I'm going with 1.5mm offset which is about 2.3°. I'll engineer some "racing tolerance" to adjust.
Mainly i was wondering what industry norms are these days? I haven't measured up a production board in some time.
-
zob
- Frequent Poster
- Posts: 476
- Joined: Tue Feb 24, 2009 1:43 pm
- Local Beach: Grado Pineta (IT), Fossalon (IT)
- Style: Freeride, strapless hooked-in
- Gear: FS S3 19m2 DLX, S3 CE 12m2 DLX & S4 8m2 DLX
Homemade Surf & Snow Boards
MBS Pro90
- Location: Iv.G.-Slovenia
-
Has thanked:
21 times
-
Been thanked:
3 times
-
Contact:
Postby zob » Fri Aug 02, 2019 11:13 am
I did ~2° offset and could feel some drag.
I also did ~2° on all 4 fins facing upwind. It was funny to ride. It was auto-carving upwind. Not a pleasant ride.
Can't beat te 0°.
OK, you can, finless
Return to “Gear Builders”
Who is online
Users browsing this forum: No registered users and 164 guests