Contact   Imprint   Advertising   Guidelines

Pocket foilboard divynicell 80 core Ghetto build tips?

Here you can exchange your experience and datas about your home build boards
merl
Frequent Poster
Posts: 207
Joined: Tue May 15, 2007 8:43 pm
Kiting since: 2001
Gear: RL kitefoil
Newind split wave

CA Pulsion 12m
FS Peak 4 5m
Gong strutted 9m
Slingshot SST 7m
Gong strutwave 5m
OR Razor 4m
Brand Affiliation: None
Location: West Sweden
Has thanked: 14 times
Been thanked: 3 times

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby merl » Tue Sep 10, 2019 4:40 pm

Back to the original topic, a high density foam ghetto build (no rocker table or vacuum). Two questions:

1 Would it be possible to bend 25mm thick 75gm2 PVC foam using a heat gun?

https://www.easycomposites.co.uk/#!/cor ... -core.html

2. What is the best way to butt-join two sheets? I guess PU glue. Any tips for pressing them together?

faklord
Frequent Poster
Posts: 291
Joined: Sun Jan 09, 2011 6:03 pm
Kiting since: 0
Brand Affiliation: None
Has thanked: 2 times
Been thanked: 7 times

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby faklord » Tue Sep 10, 2019 6:31 pm

merl wrote:
Tue Sep 10, 2019 4:40 pm
Back to the original topic, a high density foam ghetto build (no rocker table or vacuum). Two questions:

1 Would it be possible to bend 25mm thick 75gm2 PVC foam using a heat gun?

https://www.easycomposites.co.uk/#!/cor ... -core.html

2. What is the best way to butt-join two sheets? I guess PU glue. Any tips for pressing them together?
1) Yes I have done this with the exact material you linked to. It ended up a bit brown but no obvious effects to mechanical properties (didn’t go powdery or brittle). I only did this on a scrap piece to see if it worked. Didn’t go on to make a board with it. But it is what I’ll do if I make another board.

2) I just use an epoxy/microballoon goo. Clamp one part to a flat board, covered with polythene, apply goo, squish together and clamp 2nd part to same flat board. No need to “press them together” hard, so long as any gaps in the joint are filled with goo.
These users thanked the author faklord for the post:
merl (Tue Sep 10, 2019 6:41 pm)
Rating: 10%

User avatar
rynhardt
Very Frequent Poster
Posts: 931
Joined: Wed Sep 11, 2013 3:51 pm
Kiting since: 2010
Local Beach: Leeupan
Favorite Beaches: Langebaan
Style: Freeride
Gear: GK vSonic 6 & 11
Cloud C2 17
Progeni Mutare
Xelerator door
Hoff DD140
Brand Affiliation: None
Location: Johannesburg, South Africa
Has thanked: 16 times
Been thanked: 14 times

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby rynhardt » Tue Sep 10, 2019 6:56 pm

Joining the foam with a PU glue will make sanding easier. Epoxy is harder and can create a slight ridge if you sand by hand.
You can form a rocker by laminating several thin sheets together. Many thin sheets would have less spring back than fewer thick sheets.

faklord
Frequent Poster
Posts: 291
Joined: Sun Jan 09, 2011 6:03 pm
Kiting since: 0
Brand Affiliation: None
Has thanked: 2 times
Been thanked: 7 times

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby faklord » Tue Sep 10, 2019 8:20 pm

rynhardt wrote:
Tue Sep 10, 2019 6:56 pm
Joining the foam with a PU glue will make sanding easier. Epoxy is harder and can create a slight ridge if you sand by hand.
You can form a rocker by laminating several thin sheets together. Many thin sheets would have less spring back than fewer thick sheets.
Agreed. Done this. But the glue between layers adds unnecessary weight.
Kerfing is another option. My current board is this method. Just not the best aesthetically.

TomW
Very Frequent Poster
Posts: 3038
Joined: Wed Oct 05, 2005 6:43 pm
Kiting since: 2001
Local Beach: Vejbystrand, Habo Ljung, Lomma
Gear: TW Surfboards 5-0
TW Surfboards hydrofoil board 90,105,110cm
Moses Fluente 550/590 + 330/325 and 633 se
Ozone Hyperlink 9mUL, 7m
Hyperlink V2 13m
Concept Air Wave 4,5m
Brand Affiliation: None
Location: Sweden
Has thanked: 21 times
Been thanked: 68 times

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby TomW » Wed Sep 11, 2019 3:36 pm

Get one sheet of the 1080 x 1020 x 10mm. Cut it in 2 pieces and glue together - put on epoxy/glass ballon mix or use PU glue, drop it into a big garden garbage bag, Suck out the air using a vacuum cleaner and put it on some blocks of wood or books to form rocker.
With a little thinking youll figure our how to suck out the air from the bag using a regular vacuum cleaner. You might even use your kite pump that has a deflate side...use quick setting epoxy or glue.
You are building a ghetto build- so adding 200g in glue is not an issue.
But getting a good rocker is more important. Theres no reason it cannot turn out looking close to pro built board if you do a decent shaping, lamination and finishing.
And frankly, a well shaped rocker and board with a ghetto lamination and finish is perferred to a shitty shaped board with a good lamination and finish.

merl
Frequent Poster
Posts: 207
Joined: Tue May 15, 2007 8:43 pm
Kiting since: 2001
Gear: RL kitefoil
Newind split wave

CA Pulsion 12m
FS Peak 4 5m
Gong strutted 9m
Slingshot SST 7m
Gong strutwave 5m
OR Razor 4m
Brand Affiliation: None
Location: West Sweden
Has thanked: 14 times
Been thanked: 3 times

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby merl » Wed Sep 11, 2019 4:15 pm

TomW wrote:
Wed Sep 11, 2019 3:36 pm
Get one sheet of the 1080 x 1020 x 10mm. Cut it in 2 pieces and glue together - put on epoxy/glass ballon mix or use PU glue, drop it into a big garden garbage bag, Suck out the air using a vacuum cleaner and put it on some blocks of wood or books to form rocker.
With a little thinking youll figure our how to suck out the air from the bag using a regular vacuum cleaner. You might even use your kite pump that has a deflate side...use quick setting epoxy or glue.
You are building a ghetto build- so adding 200g in glue is not an issue.
But getting a good rocker is more important. Theres no reason it cannot turn out looking close to pro built board if you do a decent shaping, lamination and finishing.
And frankly, a well shaped rocker and board with a ghetto lamination and finish is perferred to a shitty shaped board with a good lamination and finish.
Would something like these work:

https://www.amazon.de/MRS-BAG-H%C3%A4ng ... U6&sr=8-42

TomW
Very Frequent Poster
Posts: 3038
Joined: Wed Oct 05, 2005 6:43 pm
Kiting since: 2001
Local Beach: Vejbystrand, Habo Ljung, Lomma
Gear: TW Surfboards 5-0
TW Surfboards hydrofoil board 90,105,110cm
Moses Fluente 550/590 + 330/325 and 633 se
Ozone Hyperlink 9mUL, 7m
Hyperlink V2 13m
Concept Air Wave 4,5m
Brand Affiliation: None
Location: Sweden
Has thanked: 21 times
Been thanked: 68 times

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby TomW » Sat Sep 14, 2019 9:48 pm

Merl, yes they do. I use them with my vacuum pump with great results, but using vacuum cleaner for ghetto v-bag is possible too.
It's cheaper and easier than using a real vacuum bag material. Trade off is bag material is stiffer and not well suited for bagging lamination around rails.

bohme
Rare Poster
Posts: 15
Joined: Fri Apr 22, 2016 12:01 pm
Kiting since: 2002
Local Beach: Ringkøbing
Favorite Beaches: Hvide Sande
Style: Foiling
Gear: Worn
Brand Affiliation: None
Has thanked: 1 time
Been thanked: 1 time

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby bohme » Sat Sep 14, 2019 11:36 pm

I made one from a single sheet of 15mm 80g/m3 PVC.
PVC is a structural core and way better than XPS and PU. No problems with heat or dents.
I laminated one side at the time with 300g/m2 biax carbon (vacuum). I just used bricks and gravity to get the rocker I wanted.
The strength is in the stringer, which includes a prefabricated KF box.
1.3kg without straps.
It obviously does not have any volume, but I prefer that.
I do not always get it right first time, but this time I did. I have used it 50+ times, and I like it a lot :-)
Attachments
20180620_073716.jpg
20180713_132817.jpg
These users thanked the author bohme for the post:
rynhardt (Sun Sep 15, 2019 9:14 am)
Rating: 10%

thewindego
Medium Poster
Posts: 129
Joined: Wed Jan 18, 2017 3:13 am
Kiting since: 2000
Local Beach: Wolfe Island
Gear: core and windego boards
Brand Affiliation: None
Has thanked: 3 times
Been thanked: 8 times
Contact:

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby thewindego » Sun Sep 15, 2019 2:51 am

Hey Bohme I give that a 10. Nice.

User avatar
omg
Very Frequent Poster
Posts: 617
Joined: Sun Oct 31, 2004 2:58 pm
Has thanked: 39 times
Been thanked: 7 times

Re: Pocket foilboard divynicell 80 core Ghetto build tips?

Postby omg » Sun Sep 15, 2019 7:32 am

Bohme, that*s an awesome board. What material is the stringer? And is the board stiff?


Return to “Gear Builders”

Who is online

Users browsing this forum: No registered users and 0 guests

cron