Contact   Imprint   Advertising   Guidelines

GoPro line mounts

Here you can exchange your experience and datas about your home build boards
TomW
Very Frequent Poster
Posts: 3295
Joined: Wed Oct 05, 2005 6:43 pm
Kiting since: 2001
Local Beach: Vejbystrand, Lomma
Gear: TW Surfboards hydrofoil board 90cm, 110cm
Gong Pro M, 90 cm mast
Ozone Hyperlink 9mUL, 7m
Hyperlink V2 13m
Concept Air Wave 4,5m
Brand Affiliation: None
Location: Sweden
Has thanked: 38 times
Been thanked: 109 times

Re: GoPro line mounts

Postby TomW » Fri May 22, 2020 10:41 pm

norcom wrote:
Thu May 21, 2020 3:55 pm
flying doctor wrote:
Thu May 21, 2020 8:13 am
So I plan to use the protective lenses next time, and can probably prevent fogging by putting it higher in the lines.
Just wondering if other max users have encountered the same problem.
The fogging is because of condensation from the warm camera and cool outside air. GoPros with cases fog up and the domes are no different. There are some ways you can prevent this (search I can't remember them off the top) but none of them are perfect. It always happens after some time and I usually just take the camera off at that point.
I talked to some engineers about this where I work( Sony) a few years back. It's a really difficult problem to solve. No one has done it yet. The cameras get very warm. We had some ideas, but the users are not screaming about it enough to incentivize the " money machine " to make the effort and spend some money to solve it.

User avatar
jakemoore
Very Frequent Poster
Posts: 1999
Joined: Tue Jan 20, 2004 3:59 am
Gear: Foil and 1strut kites.
Brand Affiliation: None
Location: Oleander
Has thanked: 50 times
Been thanked: 114 times
Contact:

Re: GoPro line mounts

Postby jakemoore » Fri May 22, 2020 11:05 pm

TomW wrote:
Fri May 22, 2020 10:41 pm
( Sony)
If you have an inside voice: it would be sweet if a cell phone size lens/sensor were encased in a tiny housing < 5 grams and attached via wire to the battery and recorder 4-5 meters away. It would take the weight out of the kite lines. Same with Max-360 style cameras. If the heavy battery was in the hand held side of a pole and the sensor/lens on the light end we would have a much better balanced pole. Radical videos create demand for the camera!

Back-Bone Ripcord is on the right track but the ribbon too big and not waterproof. https://www.back-bone.ca/product/ripcord2/

User avatar
flying doctor
Medium Poster
Posts: 143
Joined: Wed Sep 03, 2003 2:21 pm
Brand Affiliation: None
Location: Amsterdam, the Netherlands
Has thanked: 6 times
Been thanked: 15 times

Re: GoPro line mounts

Postby flying doctor » Sat May 23, 2020 1:45 pm

jakemoore wrote:
Fri May 22, 2020 11:05 pm
TomW wrote:
Fri May 22, 2020 10:41 pm
( Sony)
If you have an inside voice: it would be sweet if a cell phone size lens/sensor were encased in a tiny housing < 5 grams and attached via wire to the battery and recorder 4-5 meters away. It would take the weight out of the kite lines. Same with Max-360 style cameras. If the heavy battery was in the hand held side of a pole and the sensor/lens on the light end we would have a much better balanced pole. Radical videos create demand for the camera!

Back-Bone Ripcord is on the right track but the ribbon too big and not waterproof. https://www.back-bone.ca/product/ripcord2/
Great idea, that would be an amazing innovation for us!

Jake: any experience as to how high you can place the shape way mount above the V.
I've sent a message to the developer through the site but have received no reply.

User avatar
jakemoore
Very Frequent Poster
Posts: 1999
Joined: Tue Jan 20, 2004 3:59 am
Gear: Foil and 1strut kites.
Brand Affiliation: None
Location: Oleander
Has thanked: 50 times
Been thanked: 114 times
Contact:

Re: GoPro line mounts

Postby jakemoore » Tue May 26, 2020 5:57 pm



This is at 3 meters. It does bend the lines in so there is a force pulling the housing apart. I have a separate small piece of kite line wrapped all the way around the camera housing giving some extra strength from the lines pulling it apart. I use the same line to tie the tabs together with a square knot and a couple extra throws because the tabs aren't quite the right size for a go pro bolt and it was easier than going to buy a shorter bolt. So far so good.
flying doctor wrote:
Sat May 23, 2020 1:45 pm
how high
Last edited by jakemoore on Tue May 26, 2020 6:03 pm, edited 1 time in total.
These users thanked the author jakemoore for the post:
flying doctor (Tue May 26, 2020 6:12 pm)
Rating: 8.33%


Return to “Gear Builders”

Who is online

Users browsing this forum: No registered users and 0 guests